기기를 수리하세요 커뮤니티 상점

Eureka EasyClean 71C Power Cord Replacement

소개

While the power cord is built to last for quite a while, it can still suffer from wear-and-tear. Additionally, accidents that damage the power cord can happen. This guide covers how to replace the vacuum’s power cord.

필요한 것

  1. Eureka EasyClean 71C Power Cord Replacement, Bottom Cover: 1 단계, 이미지 1/1

    • Unscrew the two 18.1 mm PH2 Phillips head screws on the bottom of the vacuum.

    편집

  2. Eureka EasyClean 71C Power Cord Replacement: 2 단계, 이미지 1/1

    • Pry off the Riser Visor using the plastic opening tool.

    편집

  3. Eureka EasyClean 71C Power Cord Replacement: 3 단계, 이미지 1/1

    • Remove the screw cap using the metal spudger.

    • First-time removal of the screw cap can be difficult. The screw cap isn’t vital, so don’t worry about damaging the screw cap and just keep trying until it comes out.

    편집

  5. Eureka EasyClean 71C Power Cord Replacement: 4 단계, 이미지 1/2 Eureka EasyClean 71C Power Cord Replacement: 4 단계, 이미지 2/2

    • Unscrew the 14mm PH2 Phillips head screw.

    • Pull the bottom cover off of the rest of the casing.

    편집

  6. Eureka EasyClean 71C Power Cord Replacement, Casing: 5 단계, 이미지 1/1

    • Pull the power switch all the way up and remove the dust cup.

    편집

  7. Eureka EasyClean 71C Power Cord Replacement: 6 단계, 이미지 1/2 Eureka EasyClean 71C Power Cord Replacement: 6 단계, 이미지 2/2

    • Unscrew the six 18.1mm PH2 Phillips head screws on the side of the vacuum.

    • Pull the casing apart.

    편집

  8. Eureka EasyClean 71C Power Cord Replacement, Power Cord: 7 단계, 이미지 1/1

    • Pull out the switch board.

    • Ensure the vacuum is powered off and unplugged before handling any electronics.

    편집

  9. Eureka EasyClean 71C Power Cord Replacement: 8 단계, 이미지 1/2 Eureka EasyClean 71C Power Cord Replacement: 8 단계, 이미지 2/2

    • Desolder the highlighted black and white wires.

    • For instructions on how to solder and desolder wires, visit this guide.

    편집

  10. Eureka EasyClean 71C Power Cord Replacement: 9 단계, 이미지 1/1

    • Unscrew the 22.3mm PH2 Phillips head screw.

    • Remove the power cord.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 2명과 함께

Tanner Durnil

회원 가입일: 11/06/17

631 평판

안내서 6개 작성하였습니다

배지: 10

배지 +7개 더

팀

IUPUI, Team S6-G4, Baechle Fall 2017 IUPUI, Team S6-G4, Baechle Fall 2017 회원

IUPUI-BAECHLE-F17S6G4

3 회원들

안내서 12개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 8

전체 시간: 358