메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Hair Dryer Heating Element Replacement

작성자 Mitch (또 다른 기여자 9명)
  • 댓글 0
  • 즐겨찾기 5
  • 완료: 7

난이도

보통

단계

10

소요 시간

시간 제안??

섹션

3

플래그

3

Bullets!

글머리 기호!

더 나은 마크업 및 글머리 기호 색/형식 조정은 해당 안내서를 더욱 깔끔하게 만들것 입니다!

Slice and Dice

잘게 썰기

해당 안내서의 단계들은 분할되어 전제 조건 안내서들로 만들어져야 합니다.

Better Introduction

더 나은 소개글

소개글을 완성 또는 수정하여 해당 안내서를 개선하여 주십시오.

소개

Use this guide to installa replacement heating element if your hairdryer just isn't drying your hair the way it used to.

도구

해당 도구 구매

부품

No parts specified.

  1. Identify the black air concentrating nozzle.

    • Identify the black air concentrating nozzle.

    편집

  2. Remove the black air concentrating nozzle by gently twisting and pulling the nozzle.

    • Remove the black air concentrating nozzle by gently twisting and pulling the nozzle.

    편집

  3. Using a screwdriver, remove the screw located underneath the air concentrating nozzle. This screw attaches the hair dryer body to the hair dryer grating.

    • Using a screwdriver, remove the screw located underneath the air concentrating nozzle. This screw attaches the hair dryer body to the hair dryer grating.

    • The purpose of this guide is to demonstrate the repair steps for a generic hair dryer. We do not specify screw sizes because screw sizes can differ between hair dryers. For most hair dryers, use a Phillips #1 Screwdriver. For hair dryers with smaller screws, consider using a Phillips #00 Screwdriver.

    편집

  4. Detach the hair dryer grating from the body by gently twisting the grating from side to side.

    • Detach the hair dryer grating from the body by gently twisting the grating from side to side.

    편집

  5. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

  6. Separate the hair dryer grating into the three pieces seen in the image.

    • Separate the hair dryer grating into the three pieces seen in the image.

    편집

  7. Locate the screws on the handle and remove them with a Phillips screwdriver

    • Locate the screws on the handle and remove them with a Phillips screwdriver

    편집

  8. Carefully separate the plastic case using the Plastic Opening Tools

    • Carefully separate the plastic case using the Plastic Opening Tools

    편집

  9. Your hairdryer should now be disassembled. You should easily be able to see the fan, motor, heating element cover, and internal wiring.

    • Your hairdryer should now be disassembled. You should easily be able to see the fan, motor, heating element cover, and internal wiring.

    편집

  10. Remove the heat-element housing by sliding it off of the dryer.

    • Remove the heat-element housing by sliding it off of the dryer.

    편집

  11. Isolate the heating element. Use a desoldering wick and soldering iron to desolder the wires. Refer to the soldering page below.

    • Isolate the heating element. Use a desoldering wick and soldering iron to desolder the wires. Refer to the soldering page below.

    • Soldering Skills

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 7명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 9명과 함께

Mitch

회원 가입일: 2012년 10월 04일

31 평판

안내서 5개 작성하였습니다

배지: 9

배지 +6개 더

팀

Cal Poly, Team 24-29, Regan Fall 2012 Cal Poly, Team 24-29, Regan Fall 2012 회원

CPSU-REGAN-F12S24G29

5 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 9

지난 7일: 39

지난 30일: 190

전체 시간: 29,253