기기를 수리하세요 커뮤니티 상점

Joy-Con Battery Replacement

작성자 Jairo (또 다른 기여자 6명)
  • 댓글 8
  • 즐겨찾기 5
  • 완료: 37

난이도

보통

단계

5

소요 시간

5 - 10 분

섹션

1

플래그

0

소개

This guide will show you how to replace the battery in your Joy-Con controller.

There are a few minor differences between the left and right Joy-Cons. These steps apply to both Joy-Cons.

동영상 개요

  1. Remove the four Tri-Point Y00 screws from the back panel of the Joy-Con.

    • Remove the four Tri-Point Y00 screws from the back panel of the Joy-Con.

    편집

  2. Insert an Opening Pick into the bottom edge of the back panel (opposite the shoulder buttons). Slowly slide the flat edge of your Opening Pick up the side of the Joy-Con. Be careful not to slide the Opening Pick too far inside the Joy-Con. This may damage the inner components. The back panel loosens fairly easily, so not much pressure is needed.

    • Insert an Opening Pick into the bottom edge of the back panel (opposite the shoulder buttons).

    • Slowly slide the flat edge of your Opening Pick up the side of the Joy-Con.

    • Be careful not to slide the Opening Pick too far inside the Joy-Con. This may damage the inner components. The back panel loosens fairly easily, so not much pressure is needed.

    편집

  4. Open the Joy-Con like a book, with the charging rail facing away from you. Don’t try to fully remove the back panel yet. There are still two cables connecting the charging rail to the motherboard.

    • Open the Joy-Con like a book, with the charging rail facing away from you.

    • Don’t try to fully remove the back panel yet. There are still two cables connecting the charging rail to the motherboard.

    편집

  5. Use a Spudger to gently pry the battery connector from its socket on the motherboard. This will keep the Joy-Con from powering on during the repair. Use caution while working around the vibration motor cable that runs close to the battery connector. If you are replacing the battery in a right Joy-Con, you will also need to work around an antenna cable during this step. Use caution while working around the vibration motor cable that runs close to the battery connector. If you are replacing the battery in a right Joy-Con, you will also need to work around an antenna cable during this step.

    • Use a Spudger to gently pry the battery connector from its socket on the motherboard. This will keep the Joy-Con from powering on during the repair.

    • Use caution while working around the vibration motor cable that runs close to the battery connector. If you are replacing the battery in a right Joy-Con, you will also need to work around an antenna cable during this step.

    편집

  6. Insert an Opening Pick between the battery and the Joy-Con housing. Gently pry out the battery, which is lightly taped in place. To install a new battery, press it into place and reconnect it. If the double-sided tape holding the battery in place came out with the battery, replace it before you install the new battery.

    • Insert an Opening Pick between the battery and the Joy-Con housing.

    • Gently pry out the battery, which is lightly taped in place.

    • To install a new battery, press it into place and reconnect it. If the double-sided tape holding the battery in place came out with the battery, replace it before you install the new battery.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 37명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Jairo

회원 가입일: 2012년 02월 09일

4,673 평판

안내서 2개 작성하였습니다

배지: 18

배지 +15개 더

팀

iFixit iFixit 회원

Community

143 회원들

안내서 16,765개 작성하였습니다

댓글 4개

Bonjour, après avoir suivi les étapes tout fonctionne ,SAUF la recharge … à savoir également que je me suis trompé dans la commande de la nouvelle batterie, celle-ci étant d'une capacité plus faible

Ced - 답글

Bonjour Ced ! Nous sommes désolés de l’apprendre. Avez-vous essayé de calibrer la batterie ? Veuillez prendre contact avec notre service client (support@ifixit.com pour la boutique américaine ou eustore@ifixit.com pour la boutique européenne et française) en indiquant votre numéro de commande. Ce sera un plaisir de vous porter assistance !

Claire Miesch -

Bei mir ging beim roten Joy Con oder Akku nicht mehr, ich hab ihn jetzt auseinandergeschraubt, das Kabel vom Akku gelöst und wieder eingesteckt.

als ich alles zusammengebaut habe ging er. Es war wahrscheinlich nur das Kabel was nicht richtig drin war.

Tobias No name - 답글

Hello, i'm unsure what to do now but I have replaced my battery but my switch still doesn't show the presence of my right joy-con. I opened up the joy-con while connected to the switch and the battery is only charging at 1.2v (without the battery the pins are the same) could it be the charging rail? Any tips would be appreciated. Thanks!

Logan Marynowich - 답글

댓글 쓰기

조회 통계:

24 시간 전: 74

7일 전: 353

30일 전: 1,511

전체 시간: 53,029