Logitech G502 Lightspeed Battery Replacement

소개

Use this guide to replace a worn-out or dead battery in your Logitech G502 Lightspeed.

If you plan to reuse the mouse feet, you’ll need to apply heat to loosen the adhesive and remove the feet with minimal bending. Bent or torn mouse feet may require replacement.

If the battery is swollen, take appropriate precautions. For your safety, discharge your battery below 25% before disassembling your device. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

You might need replacement adhesive to reattach the new battery. Check the guide and your replacement battery in advance.

필요한 것

1 단계 Switch the mouse off

Logitech G502 Lightspeed Battery Replacement, Switch the mouse off: 1 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Switch the mouse off: 1 단계, 이미지 2/2

Before you begin, flip the power switch into the OFF position.

편집

2 단계 Heat the mouse feet

Logitech G502 Lightspeed Battery Replacement, Heat the mouse feet: 2 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Heat the mouse feet: 2 단계, 이미지 2/2

Heat an iOpener and apply it to the mouse feet for one minute.
You may use a hair dryer or heat gun. If you do, set it to the lowest temperature setting and apply heat for 10 seconds.

편집

3 단계 Remove the front foot

Logitech G502 Lightspeed Battery Replacement, Remove the front foot: 3 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Remove the front foot: 3 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Remove the front foot: 3 단계, 이미지 3/3

Insert the tip of an opening pick underneath the front foot at the gap in its recess.
The mouse feet are made of two layers. Make sure you insert the pick under the bottom layer to completely remove the foot.
When possible, grab with your fingers and slowly pull to peel it off completely.

편집

4 단계 Remove the front right foot

Logitech G502 Lightspeed Battery Replacement, Remove the front right foot: 4 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Remove the front right foot: 4 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Remove the front right foot: 4 단계, 이미지 3/3

Insert the tip of an opening pick underneath the tiny front right foot at the gap in its recess.

편집

5 단계 Remove the rear foot

Logitech G502 Lightspeed Battery Replacement, Remove the rear foot: 5 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Remove the rear foot: 5 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Remove the rear foot: 5 단계, 이미지 3/3

Insert the tip of an opening pick underneath the rear foot starting at the gap in its recess.
When possible, grab with your fingers and slowly pull to peel it off completely.

편집

6 단계 Remove the weight hatch

Logitech G502 Lightspeed Battery Replacement, Remove the weight hatch: 6 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Remove the weight hatch: 6 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Remove the weight hatch: 6 단계, 이미지 3/3

Use your fingers to remove the weight hatch by pulling the bottom part of the thumb rest straight down.

편집

7 단계 Remove the bottom screws

Logitech G502 Lightspeed Battery Replacement, Remove the bottom screws: 7 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Remove the bottom screws: 7 단계, 이미지 2/2

Remove the four 5.4 mm long Phillips screws at the underside of the mouse.

편집

8 단계 Unclip the bottom plate

Logitech G502 Lightspeed Battery Replacement, Unclip the bottom plate: 8 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Unclip the bottom plate: 8 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Unclip the bottom plate: 8 단계, 이미지 3/3

Insert an opening pick between the bottom plate and the upper shell starting at the rear of the mouse.
Slide the opening pick along the gap between the two halves towards the outer flank of the mouse.
Twist the opening pick to disengage the clips holding both halves together.
This might require more force than anticipated.

편집

9 단계

Logitech G502 Lightspeed Battery Replacement: 9 단계, 이미지 3/3

Again insert the tip of an opening pick between the bottom plate and the top shell starting at the rear.
Slide the pick along the gap between the two halves towards the thumb rest.
Make sure to follow the curved geometry to keep the pick in the gap.
Twist the opening pick to unhinge the remaining clips.
This also might require more force than anticipated.

편집

10 단계 Hinge open the top shell

Logitech G502 Lightspeed Battery Replacement, Hinge open the top shell: 10 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Hinge open the top shell: 10 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Hinge open the top shell: 10 단계, 이미지 3/3

Flip the mouse over on its (removed) feet and hinge the top shell open towards the right side.
Don’t remove the top shell all the way yet. It is still connected to the bottom plate via cables.

편집

11 단계 Disconnect the battery

Logitech G502 Lightspeed Battery Replacement, Disconnect the battery: 11 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Disconnect the battery: 11 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Disconnect the battery: 11 단계, 이미지 3/3

Hold the battery cable close to the connector and carefully "walk it out" by pulling parallel to the motherboard rocking the connector side to side.

편집

12 단계 Disconnect the interconnect cables

Logitech G502 Lightspeed Battery Replacement, Disconnect the interconnect cables: 12 단계, 이미지 1/3

Logitech G502 Lightspeed Battery Replacement, Disconnect the interconnect cables: 12 단계, 이미지 2/3

Logitech G502 Lightspeed Battery Replacement, Disconnect the interconnect cables: 12 단계, 이미지 3/3

Use a spudger or your fingernail to flip up the small, hinged locking flap of both ZIF connectors to disconnect and free the interconnect cables.
If the cables don’t pop out by themselves use your fingers to lift them out of the sockets.

편집

13 단계 Loosen the battery

Logitech G502 Lightspeed Battery Replacement, Loosen the battery: 13 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Loosen the battery: 13 단계, 이미지 2/2

Insert the tip of an opening pick between the battery and its plastic tub.
Use an opening pick to pry the battery up slightly to loosen the adhesive underneath.

편집

14 단계 Get underneath the battery

Logitech G502 Lightspeed Battery Replacement, Get underneath the battery: 14 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Get underneath the battery: 14 단계, 이미지 2/2

Push the opening pick all the way under the battery.

편집

15 단계 Remove the battery

Logitech G502 Lightspeed Battery Replacement, Remove the battery: 15 단계, 이미지 1/2

Logitech G502 Lightspeed Battery Replacement, Remove the battery: 15 단계, 이미지 2/2

The battery adhesive will now stick mostly to the opening pick.
Slowly pull the opening pick towards the rear of the mouse to slide the battery out from under the plastic tab and out of its tub.

편집

결론

If possible, turn on your device and test your repair before installing new adhesive and resealing.

Secure the new battery with pre-cut adhesive or double-sided adhesive tape if the battery comes without one. Press the new battery firmly into place.

To reassemble your device, follow these instructions in reverse order. Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

For optimal performance, calibrate your newly installed battery: Charge it to 100% and keep charging it for at least 2 more hours. Then use your device until it shuts off due to low battery. Finally, charge it uninterrupted to 100%.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.