메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

MacBook Pro 15" Unibody Mid 2009 Left Fan Replacement

작성자 Walter Galan (또 다른 기여자 6명)
  • 댓글 3
  • 즐겨찾기 15
  • 완료: 66

난이도

보통

단계

4

소요 시간

5 - 40 분

섹션

2

플래그

0

소개

Replace a faulty fan to keep temperatures down.

도구

해당 도구 구매

부품

해당 부품 구매

  1. Remove the following ten screws securing the lower case to the upper case:

    • Remove the following ten screws securing the lower case to the upper case:

    • Seven 3 mm Phillips screws.

    • Three 13.5 mm Phillips screws.

    편집

  2. Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case. Remove the lower case and set it aside.

    • Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.

    • Remove the lower case and set it aside.

    편집

  3. PC 노트북 배터리

    큰 전력 향상을 위한 손쉬운 수리.

    지금 장보기

    PC 노트북 배터리

    큰 전력 향상을 위한 손쉬운 수리.

    지금 장보기

  4. Use the flat end of a spudger to disconnect the left fan connector from the logic board. It is useful to twist the spudger axially from beneath the fan cable wires to release the connector. The fan socket and the fan connector can be seen in the second and third pictures. Be careful not to break the plastic fan socket off the logic board as you use your spudger to lift the fan connector straight up and out of its socket. The layout of the logic board shown in the second picture may look slightly different than your machine but the fan socket is the same.

    • Use the flat end of a spudger to disconnect the left fan connector from the logic board.

    • It is useful to twist the spudger axially from beneath the fan cable wires to release the connector.

    • The fan socket and the fan connector can be seen in the second and third pictures. Be careful not to break the plastic fan socket off the logic board as you use your spudger to lift the fan connector straight up and out of its socket. The layout of the logic board shown in the second picture may look slightly different than your machine but the fan socket is the same.

    편집

  5. Remove three T6 Torx screws securing the left fan to the logic board. Lift the left fan out of the upper case.

    • Remove three T6 Torx screws securing the left fan to the logic board.

    • Lift the left fan out of the upper case.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 66명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Walter Galan

601,438 평판

안내서 1,203개 작성하였습니다

배지: 53

배지 +50개 더

댓글 2개

의견 추가하세요

Connecting the fan to the logic board is unclear. Could you walk through that a little more clearly?

kamoako1 - 답글

When connecting the new fan to the logic board, set the connector piece above its socket on the logic board and then gently press down. It should click together.

k. -

댓글 쓰기

조회 통계:

지난 24시간: 3

지난 7일: 13

지난 30일: 43

전체 시간: 39,735