기기를 고치세요

수리할 권리

부품 & 도구

Microsoft Surface Pro Charging Port Replacement

작성자 Jonathan Choi (또 다른 기여자 7명)
  • 댓글 3
  • 즐겨찾기 1
  • 완료: 1

난이도

보통

단계

12

소요 시간

15 - 30 분

섹션

2

플래그

1

Needs Better Images

더 나은 이미지가 필요함

더 나은 사진은 해당 안내서를 향상시킬 것입니다. 사진 촬영, 편집, 또는 새로운 업로드를 도와주십시오!

소개

Use this guide to replace the charging port in a Microsoft Surface Pro.

  1. Use a heated iOpener or a heat gun to heat the edges of the display and soften its adhesive.

    • Use a heated iOpener or a heat gun to heat the edges of the display and soften its adhesive.

    • If you're using an iOpener it may take several cycles of reheating and applying it to soften the adhesive enough. Every time, let the iOpener sit on the display for at least a minute before reheating to allow the adhesive to soften.

    편집

  2. Apply a suction cup as close as possible to the edge of the display. Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.

    • Apply a suction cup as close as possible to the edge of the display.

    • Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.

    • Slide the opening pick all the way around the edges of the display to cut through the adhesive on the bezel.

    • Do not insert the opening pick past the bezel of the display—you may permanently damage the display.

    • Be very careful and move slowly during this step. The display is fragile and will crack if too much force is applied against it. If your tools seem stuck, apply more heat to further soften the adhesive.

    편집

  3. Starting from the top edge, lift the display slightly. If you feel any resistance, use heat and an opening pick to slice through any remaining adhesive. Before completely removing the display, disconnect the three display cables.

    • Starting from the top edge, lift the display slightly. If you feel any resistance, use heat and an opening pick to slice through any remaining adhesive.

    • Before completely removing the display, disconnect the three display cables.

    편집

  4. Remove the display.

    • Remove the display.

    편집

  5. Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

    Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

  6. Using a T5 Torx screwdriver, unscrew a total number of 23 screws located on the outside panel of the Surface Pro. Using a T5 Torx screwdriver, unscrew a total number of 23 screws located on the outside panel of the Surface Pro.

    • Using a T5 Torx screwdriver, unscrew a total number of 23 screws located on the outside panel of the Surface Pro.

    편집

  7. Use the plastic opening tool or fingers to pry out the front camera.

    • Use the plastic opening tool or fingers to pry out the front camera.

    편집

  8. Lift the outside panel from the Surface Pro

    • Lift the outside panel from the Surface Pro

    편집

  9. Use the T5 torx screw driver to unscrew the 6 T5 screws in the left and right outside metal panels Use the T2 torx screw driver to unscrew the 23 T2 screws on the left and right outside metal panels

    • Use the T5 torx screw driver to unscrew the 6 T5 screws in the left and right outside metal panels

    • Use the T2 torx screw driver to unscrew the 23 T2 screws on the left and right outside metal panels

    편집

  10. Pull out left and right metal panels with hands

    • Pull out left and right metal panels with hands

    편집

  11. Pull out the orange charging port strip using tweezers

    • Pull out the orange charging port strip using tweezers

    편집

  12. Unscrew the two T5 torx screws located on each side of the charging port.

    • Unscrew the two T5 torx screws located on each side of the charging port.

    편집

  13. Once you have unscrewed the charging port, you can gently pull it out with your hands.

    • Once you have unscrewed the charging port, you can gently pull it out with your hands.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Jonathan Choi

회원 가입일: 2013년 10월 09일

678 평판

안내서 4개 작성하였습니다

배지: 12

배지 +9개 더

팀

Cal Poly, Team 8-20, Regan Fall 2013 Cal Poly, Team 8-20, Regan Fall 2013 회원

CPSU-REGAN-F13S8G20

4 회원들

안내서 11개 작성하였습니다

댓글 3개

의견 추가하세요

Where do you get a replacement charging port at?

Evil Robot - 답글

Agree where can you get the port?

J-M. M. - 답글

Same instructions for changing the port on a surface pro 2?

Robert - 답글

댓글 쓰기

조회 통계:

24 시간 전: 9

7일 전: 58

30일 전: 248

전체 시간: 15,104