기기를 수리하세요 커뮤니티 상점

Netgear WGR614v9 Antenna Replacement

소개

This guide will take you through the process involved with installing an antenna. De-soldering and soldering will be required.

필요한 것

  1. Netgear WGR614v9 Antenna Replacement, Lower Case: 1 단계, 이미지 1/1

    • Rotate the device so that the bottom is facing up.

    편집

  2. Netgear WGR614v9 Antenna Replacement: 2 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement: 2 단계, 이미지 2/2

    • Lift up all four rubber pads on the bottom of the router with the plastic opening tool.

    • Be careful not to pull the rubber pads all the way out when lifting as they are difficult to reinsert.

    편집

  3. Netgear WGR614v9 Antenna Replacement: 3 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement: 3 단계, 이미지 2/2

    • Unscrew the four 11.8 mm T-8 torx screws from the bottom of the router.

    편집

  4. Netgear WGR614v9 Antenna Replacement: 4 단계, 이미지 1/1

    • Lift the bottom casing straight up from the router.

    편집

  6. Netgear WGR614v9 Antenna Replacement, Motherboard: 5 단계, 이미지 1/1

    • Remove the clear plastic casing by lifting it straight up from the router.

    편집

  7. Netgear WGR614v9 Antenna Replacement: 6 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement: 6 단계, 이미지 2/2

    • Separate the motherboard from the top shell by lifting it straight up from the router.

    편집

  8. Netgear WGR614v9 Antenna Replacement, Antenna: 7 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement, Antenna: 7 단계, 이미지 2/2

    • Rotate the motherboard so that the top is facing up.

    • Set the motherboard on a flat clean surface.

    편집

  9. Netgear WGR614v9 Antenna Replacement: 8 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement: 8 단계, 이미지 2/2

    • Do not refer to the pictures in this step for proper de-soldering and soldering techniques. They are for illustration purposes only.

    • Refer to this link for proper de-soldering and soldering techniques.

    • Be patient. This may take some time depending on the quality of your soldering iron.

    편집

  10. Netgear WGR614v9 Antenna Replacement: 9 단계, 이미지 1/1

    • Peel off the yellow tape holding the wires.

    • Set the tape aside on a clean surface so that it can be reused.

    편집

  11. Netgear WGR614v9 Antenna Replacement: 10 단계, 이미지 1/2 Netgear WGR614v9 Antenna Replacement: 10 단계, 이미지 2/2

    • Extend the antenna outwards from the device so that it is straight.

    • Locate the clips that hold the antenna onto the router.

    • Push the clips in with one hand and pull the antenna out with your other hand. Slightly twist the antenna until it becomes free from the hole.

    편집

  12. Netgear WGR614v9 Antenna Replacement: 11 단계, 이미지 1/1

    • Pull out the antenna as well as the connected wire.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Ryan Murphy

회원 가입일: 10/03/11

488 평판

안내서 4개 작성하였습니다

배지: 11

배지 +8개 더

팀

Cal Poly, Team 21-24, Maness Fall 2011 Cal Poly, Team 21-24, Maness Fall 2011 회원

CPSU-MANESS-F11S21G24

4 회원들

안내서 11개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 2

전체 시간: 7,570