기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Olympus D590 Logic Board Replacement

소개

This guide will take you through all the steps to sucessfully install a new logic board to your Olympus D590 camera.

필요한 것

  1. Olympus D590 Logic Board Replacement, Face Plate: 1 단계, 이미지 1/1

    • Remove five baseplate screws using a Phillips #00 screwdriver.

    번역하기

  2. Olympus D590 Logic Board Replacement: 2 단계, 이미지 1/1

    • Press and slide the battery cover retainer clip to the left. Use tweezers to lift the battery cover away.

    번역하기

  3. Olympus D590 Logic Board Replacement: 3 단계, 이미지 1/1

    • Remove the single screw from the battery housing using a Phillips #00 screwdriver.

    번역하기

  4. Olympus D590 Logic Board Replacement: 4 단계, 이미지 1/1

    • Using tweezers, lift the rubber plate to expose the ports.

    번역하기

  6. Olympus D590 Logic Board Replacement: 5 단계, 이미지 1/1

    • Remove two screws from the ports using a Phillips #00 screwdriver.

    번역하기

  7. Olympus D590 Logic Board Replacement: 6 단계, 이미지 1/1

    • Use a spudger to pry the faceplate away from the rest of the camera.

    번역하기

  8. Olympus D590 Logic Board Replacement: 7 단계, 이미지 1/1

    • To avoid disconnection of the connector line to the motherboard, use caution when pulling faceplate away from camera case.

    • Damage to the connector line will prevent the on/off power switch's operational function.

    번역하기

  9. Olympus D590 Logic Board Replacement, Logic Board: 8 단계, 이미지 1/1

    • Unscrew all 4 circled screws.

    번역하기

  10. Olympus D590 Logic Board Replacement: 9 단계, 이미지 1/1

    • The logic board should now be loose and easily liftable.

    • DO NOT lift the board out completely the wiring that is still connected must be disconnected before proceeding.

    번역하기

  11. Olympus D590 Logic Board Replacement: 10 단계, 이미지 1/3 Olympus D590 Logic Board Replacement: 10 단계, 이미지 2/3 Olympus D590 Logic Board Replacement: 10 단계, 이미지 3/3

    • Disconnect the 3 wiring strips from the device by gently pulling with tweasers from the base of the strip.

    • Do not use sharp tweasers because the wiring might tear.

    • Make sure to use small force so the wiring is not damaged. It may help to gently wiggle the tape.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 7명과 함께

Sara

회원 가입일: 04/15/10

84 평판

안내서 2개 작성하였습니다

배지: 6

배지 +3개 더

팀

Cal Poly, Team 28-23, Regan Spring 2010 Cal Poly, Team 28-23, Regan Spring 2010 회원

CPSU-REGAN-S10S28G23

4 회원들

안내서 14개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 2

전체 시간: 1,767