주요 콘텐츠로 건너뛰기

소개

The rechargeable battery provides power to the device. It will need to be replaced if it is damaged or wears out with use. Some steps in this procedure require desoldering connections. For a review of soldering techniques, check out this How to Solder Guide.

  1. Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees. Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees. Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.
    • Use the charging station to remove the a small plastic plug from the end of the toothbrush by inserting the charging station into the end insert and twisting counter-clockwise by 90 degrees.

  2. Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.
    • Remove the end cap from the bottom of the toothbrush by prying it off with a spudger.

  3. Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.
    • Remove the top cap by using a spudger to pry the plastic ring off of the toothbrush frame.

  4. Push on the rotating head in order to pop the assembly out of the black plastic casing. You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.
    • Push on the rotating head in order to pop the assembly out of the black plastic casing.

    • You can also use a spudger to leverage the assembly out, but this may break the copper wire connected to the induction coil, so be careful.

  5. Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.
    • Unwrap the ends of the wires from the white plastic pegs using a pair of tweezers.

    • Each wire end is wrapped around the peg 3-4 times.

  6. Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.
    • Melt the solder at the two pads on either side of the top of the motherboard. This will require a high heat soldering iron. Remove the wire from the solder pads using tweezers once the solder melts.

  7. Remove the induction coil by pulling the plastic tabs out of their keepers.
    • Remove the induction coil by pulling the plastic tabs out of their keepers.

    • A spudger can be used to remove the plastic tabs from their keepers if neccessary.

  8. Remove the spring from the housing using a nylon spudger.
    • Remove the spring from the housing using a nylon spudger.

  9. Use a soldering iron to melt the solder pad at the top of the motherboard, which attaches a battery electrode to the board. Remove the electrode by pulling it through the plastic housing after it has been desoldered from the board. Repeat with the two solder pads on either side of the motherboard just above the black diamond-shaped component. The electrode foils can be pulled through the board from the back after the solder is melted.
    • Use a soldering iron to melt the solder pad at the top of the motherboard, which attaches a battery electrode to the board. Remove the electrode by pulling it through the plastic housing after it has been desoldered from the board.

    • Repeat with the two solder pads on either side of the motherboard just above the black diamond-shaped component. The electrode foils can be pulled through the board from the back after the solder is melted.

  10. Use a metal spudger to pop the battery out of its casing. The electrodes will remain attached to the battery.
    • Use a metal spudger to pop the battery out of its casing. The electrodes will remain attached to the battery.

결론

To reassemble your device, follow these instructions in reverse order.

다른 4명이 해당 안내서를 완성하였습니다.

Jonathan Bowyer

회원 가입일: 2017년 11월 06일

359 평판

안내서 3개 작성하였습니다

IUPUI, Team S1-G1, Harley Fall 2017 IUPUI, Team S1-G1, Harley Fall 2017 회원

IUPUI-HARLEY-F17S1G1

3 회원들

안내서 8개 작성하였습니다

Wo bekommt man einen neuen AKU

Andreas

Andreas Kappos - 답글

Der sollte es sein. Er muss Lötfahnen haben! Miss die Länge nach, 42 oder 48 mm.

https://www.amazon.de/Ersatzakku-mit-Ein...

VauWeh -

댓글 쓰기

조회 통계:

24 시간 전: 9

7일 전: 53

30일 전: 288

전체 시간: 18,166