기기를 수리하세요 커뮤니티 상점

Protocol Dronium III AP Light Bulb Replacement

소개

This guide provides instructions for the removal and re-installation of the drone L.E.D. bulbs. This guide requires soldering. Please see this guide for more information on how to solder and desolder connections.

필요한 것

  1. Protocol Dronium III AP Light Bulb Replacement, Drone Battery Pack: 1 단계, 이미지 1/2 Protocol Dronium III AP Light Bulb Replacement, Drone Battery Pack: 1 단계, 이미지 2/2

    • Ensure the drone is powered off.

    • Press in and lift battery compartment cover.

    • A soft pry tool may be used for easier access.

    편집

  2. Protocol Dronium III AP Light Bulb Replacement: 2 단계, 이미지 1/1

    • Remove battery pack from body of drone.

    편집

  3. Protocol Dronium III AP Light Bulb Replacement: 3 단계, 이미지 1/2 Protocol Dronium III AP Light Bulb Replacement: 3 단계, 이미지 2/2

    • Disconnect white connectors between the battery pack and drone.

    편집

  5. Protocol Dronium III AP Light Bulb Replacement, L.E.D. Bulb(s): 4 단계, 이미지 1/1

    • Remove the eight (8) 5mm Philips screws attaching the motor arms to the body using a Philips J00 screwdriver.

    편집

  6. Protocol Dronium III AP Light Bulb Replacement: 5 단계, 이미지 1/2 Protocol Dronium III AP Light Bulb Replacement: 5 단계, 이미지 2/2

    • Remove the six (6) 5mm Philips screws attaching the Body Cover to the Body of the drone using a Philips J00 screwdriver.

    • Remove the Body Cover.

    편집

  7. Protocol Dronium III AP Light Bulb Replacement: 6 단계, 이미지 1/2 Protocol Dronium III AP Light Bulb Replacement: 6 단계, 이미지 2/2

    • Remove the two (2) 5mm Philips screws attaching the Motherboard to the body of the drone using a Philips J00 screwdriver.

    • Lift the Motherboard off the mounting position.

    • Do not pull hard on the Motherboard as solder connections are fragile.

    편집

  8. Protocol Dronium III AP Light Bulb Replacement: 7 단계, 이미지 1/2 Protocol Dronium III AP Light Bulb Replacement: 7 단계, 이미지 2/2

    • This step contains a tool that can present a potential burn hazard.

    • Prepare and warm up a soldering iron.

    • Position Motherboard so that the L.E.D. bulb solder joints are accessible.

    • Use the soldering iron to melt the solder joints.

    • For more detailed instructions on how to solder, visit out How to Solder and Desolder Connections guide.

    • Remove the L.E.D. bulb from the Motherboard

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Steven Mooers

회원 가입일: 10/18/17

401 평판

안내서 4개 작성하였습니다

배지: 4

+1개 배지 추가

팀

UW Tacoma, Team S1-G1, Rose Fall 2017 UW Tacoma, Team S1-G1, Rose Fall 2017 회원

UWT-ROSE-F17S1G1

4 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 2

전체 시간: 210