기기를 수리하세요 커뮤니티 상점

Ryobi CSB125 Motor Replacement

소개

This guide will show you how to properly access the internals to the motor housing to your Ryobi CSB125 circular saw. If you hear a humming noise when pressing the trigger, or while operating the saw smoke forms, then most likely the motor has gone bad. This troubleshooting page will help diagnose any potential problems occurring due to a faulty motor. In the event that a new motor is needed, this guide will show the steps to properly install a new one. The only tools you will need are a #2 Phillips screwdriver, a 7”/32 allen key, and a T20 torx screwdriver.

필요한 것

  1. Ryobi CSB125 Motor Replacement, Motor: 1 단계, 이미지 1/1

    • Place the saw on a flat surface with the blade facing up.

    • Make sure that the saw is unplugged from any power source.

    편집

  2. Ryobi CSB125 Motor Replacement: 2 단계, 이미지 1/2 Ryobi CSB125 Motor Replacement: 2 단계, 이미지 2/2

    • Remove the bumper by using the T20 torx screwdriver to loosen the M5 x 20mm screw.

    편집

  3. Ryobi CSB125 Motor Replacement: 3 단계, 이미지 1/2 Ryobi CSB125 Motor Replacement: 3 단계, 이미지 2/2

    • Use the 7”/32 allen key to loosen the 5/16-18 x 9/16 in. blade screw.

    편집

  4. Ryobi CSB125 Motor Replacement: 4 단계, 이미지 1/1

    • Remove the 5/16-18 x 9/16 in. blade screw, spring washer, the outer blade washer, the blade, and the inner blade washer.

    편집

  6. Ryobi CSB125 Motor Replacement: 5 단계, 이미지 1/3 Ryobi CSB125 Motor Replacement: 5 단계, 이미지 2/3 Ryobi CSB125 Motor Replacement: 5 단계, 이미지 3/3

    • Use the #2 Phillip screwdriver to remove the four M4x16mm screws shown.

    • You will need to rotate the protective shell around in order to access them.

    편집

  7. Ryobi CSB125 Motor Replacement: 6 단계, 이미지 1/1

    • Remove the lower blade guard support assembly from the rest of the saw.

    편집

  8. Ryobi CSB125 Motor Replacement: 7 단계, 이미지 1/1

    • Flip the saw over and place the saw down on a flat surface with the motor facing up.

    편집

  9. Ryobi CSB125 Motor Replacement: 8 단계, 이미지 1/1

    • Use the Phillips #2 screwdriver to remove the five M4x16mm screws.

    편집

  10. Ryobi CSB125 Motor Replacement: 9 단계, 이미지 1/1

    • Use the Phillips #2 screwdriver to remove the two M45x35mm screws.

    편집

  11. Ryobi CSB125 Motor Replacement: 10 단계, 이미지 1/2 Ryobi CSB125 Motor Replacement: 10 단계, 이미지 2/2

    • Use the Phillips #2 screwdriver to remove the two M4x16mm screws holding down the end cover.

    • Pull off the end cover.

    편집

  12. Ryobi CSB125 Motor Replacement: 11 단계, 이미지 1/1

    • Use the Phillips #2 screwdriver to remove the M45x35mm screw holding down the motor housing.

    편집

  13. Ryobi CSB125 Motor Replacement: 12 단계, 이미지 1/1

    • Remove the motor housing for access to the internal motor components.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 1명과 함께

Curtis Melo

회원 가입일: 10/31/19

1,066 평판

안내서 5개 작성하였습니다

배지: 10

배지 +7개 더

팀

UMass Dartmouth, Team S2-G1, Barthe Fall 2019 UMass Dartmouth, Team S2-G1, Barthe Fall 2019 회원

UMASSD-BARTHE-F19S2G1

3 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 8

전체 시간: 563