이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
Lift the battery out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the keyboard release tabs (shown in yellow) toward you and lift up on the keyboard until it pops free.
-
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (shown in orange) 180 degrees in either direction and try again.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push in the thin rims of the lower case surrounding the battery compartment, bending them past the tabs, and then lift up to free that corner of the lower case.
This part scared me, never in an iFixIt guide have I seen a warning like "trying times are ahead".
I used a plastic iPod opening tool and ran it around the seam in the same order pictured. I had the plastic off in less than a minute with almost no fuss.
PohTayToez - 답글
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
Paulix로 부터 인용:
I found it easier and "safer" to use a spudge at the back as well (two on each side of the hinge)
I did too. Thanks, Paulix.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single Phillips screw securing the DC-In board.
You might not need to remove the entire DC-In board and cable. This is removed because the DC-In jack blocks the upper case from being lifted off. I just removed the screw and pushed the board slightly in when removing the upper case to provide clearance. You may want to tape the board loosely in place when the screw is out to prevent it from falling out.
georgie333 - 답글
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Angle the DC-In board out of its compartment.
beefybov로 부터 인용:
You need to undo the adhesive halfway down the cable, so you can lift the DC board to angle it out correctly. beefybov
Good call, beefybov.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn over the computer and open it.
-
Remove the 3 Phillips screws from the edges of the keyboard area.
A soft cloth like the one you use to clean your screen with. Not a towel because of the static that might be built up in heavier fabrics.
2myownbeat - 답글
The picture has the lower *right* screw marked as "L" -- but that's a mistake; the short screw is, as described, on the lower LEFT side.
Peter King - 답글
On my computer, the screw in lower right marked "L" (long?) in the picture is M3x6mm and the other two are M3x3mm.
Yes, the LONG screw goes into the bottom RIGHT corner if the screen is facing you as it does when you're using the computer.
Sugar Fish - 답글
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails, carefully pry the connector from its socket.
-
Carefully disconnect the multicolored speaker cable from the logic board in the same fashion.
This is a very tough one. I did break both the power cable and speaker cable off the motherboard, and was unable to separate the motherboard-side connectors from the cable-side connectors even after that. Fortunately, this iBook was already bricked.
Sugar Fish - 답글
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips.
-
Two 4 mm Phillips.
Ditto
2myownbeat - 답글
The little tabs on the shield that are intended to contact the metal on the ports and the optical drive had been flattened out on my iBook and were no longer in contact. I didn't notice this until I had installed the shield. Make sure the tabs are bent down a bit as to contact the ports and optical drive. This system looks like it replaced the foil tape on earlier models. Just my own observation.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the top shield up from the right side, minding the upper left corner which may catch on the metal framework.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two Phillips screws at the corners of the modem.
-
Remove the two Phillips screws at the corners of the modem.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to pry the modem up from the end nearest the AirPort card to separate its connector from a socket on the logic board.
-
Use your hands to seperate the modem from the modem shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three 3 mm Phillips screws securing the AirPort card bracket to the framework.
-
Lift the AirPort card bracket up and out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 3 mm Phillips screws securing the AirPort card to the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Using a spudger, pry up on the AirPort card from the end nearest the hard drive to separate the connector from the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to disconnect the two antenna cables from the AirPort card.
-
Remove the AirPort card from the computer and set it aside.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
De-route the antenna wires from above the heat sink, around the RAM socket, and below the optical drive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the computer back over.
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the display up and tilt it backwards, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
다른 14명이 해당 안내서를 완성하였습니다.
첨부 문서
댓글 2개
Smooth as silk Walter. I am changing this to try and address a Black screen problem. After a Optical Drive and HD (OWC Legacy SSD) my machine went from perfect to normal boot then 28-30 secs later, black screen while everything else worked (caps lock light, pulsing sleep light, etc.) Will let you know if this solved the prob as I have a screen harvested years ago from a working iBook of mine.
Thanks
Nothing yet Walter. The past couple of weeks I have dismantled my iBook 14” 1.42 and put it back together a half dozen times or so. I’ve bought parts off of ebay, harvested stuff from my spare iBook and I am certain of this... It still loads as normal as can be. Bright screen, sound, etc. but 38 secs from first desktop view and 28-30 secs after complete load it gets a black screen.
I’ve checked or replaced: RAM, Inverter cable, HD, different display, and more. I’ve tried rushing to the sys prefs and setting it to “no sleep.” I’ve quickly opened a song in Quicktime and it shuts off with the screen goes black.
Any other suggestions from anyone would be great. I really dig my iBook and it was working fine until I replaced the Optical drive (now gone) and at one point I started it up with only the aluminum shields on and it worked fine. Then, after putting the cases back together, nothing since.