이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
-
냄비나 팬에 iOpener가 완전히 잠길 정도로 충분한 물을 채우세요.
-
물이 끓을 때까지 가열하세요. 불을 끄세요.
-
iOpener를 뜨거운 물에 2~3분간 담그세요. iOpener가 물에 완전히 잠겼는지 확인합니다.
-
집게를 사용하여 뜨거운 물에서 가열된 아이오페너를 꺼내세요.
-
수건으로 iOpener를 완전히 말리세요.
-
iOpener를 사용할 준비가 되었습니다! iOpener를 재가열해야 한다면 물을 끓인 후 불을 끄고 2~3분 동안 iOpener를 물에 담가 두세요.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.
-
Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully place a suction cup halfway up the heated side.
-
Be sure the cup is completely flat on the screen to get a tight seal.
-
While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.
-
Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat and reapply the iOpener.
-
Let it rest for a few minutes to reheat the left edge of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue moving the opening pick down the side of the display to release the adhesive.
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Take the first pick you inserted and slide it up toward the top corner of the iPad.
-
If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opening pick around the top left corner of the iPad to separate the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the opening pick in the iPad slightly past the front-facing camera.
-
Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive.
-
Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
-
Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the top right opening pick around the corner to fully release the top edge of the glass.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to slide the pick down the right edge of the iPad, releasing the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the opening picks in place and reheat the iOpener.
-
Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the lower left pick to the lower left corner to cut the adhesive on that corner.
-
Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.
-
Antennas
-
Home button cavity
-
Digitizer cable
-
The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
With a new pick, slice gently over the left-hand antenna, stopping before the home button.
-
Leave the pick in place before moving on.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.
-
Insert the pick slightly deeper and work it back toward the home button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift slowly and gently to further detach the adhesive along the lower edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.
-
Return the front-facing camera housing to its recess in the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Tweezers$4.99-
Remove the following Phillips #00 screws securing the LCD:
-
Three 3.3 mm screws
-
One 4.5 mm screw
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Hold the LCD with one hand, and the rear body of the iPad with the other.
-
Gently pull the LCD away from the speakers to separate the tape, being careful not to pull on the digitizer cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.
-
Lay the LCD on the front panel glass to allow access to the display cables.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the tip of a spudger between the LCD and the adhesive tabs to free the display.
-
Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad.
-
Remove the LCD shield plate.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following Phillips #00 screws from the display cable bracket:
-
One 2.7 mm screw
-
Two 1.4 mm screws
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat tip of a spudger to gently lift the battery connector up off its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use spudger to lift the LCD connector up off its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to lift the digitizer cable connector straight up off of its socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the spudger under the battery side of the digitizer board to begin separating it from the rear case.
-
Lift the digitizer board up to free the last of the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
On the replacement front panel, remove the small piece of adhesive backing from the digitizer cable.
-
Fold the digitizer cable back over onto itself and press firmly to secure the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Peel the large clear plastic liner off of the inside of the glass.
-
Peel any blue plastic backings covering the adhesive around the perimeter of the front panel assembly.
-
Don't remove any copper coverings from the outlined region, such as yellow kapton tape or black electrical tape.
-
Ensure the glass panel is free of fingerprints and grime before installing it on your device.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place the edge of a plastic opening tool on each side of the magnet near the top left corner of the front panel assembly.
-
Carefully wedge the edge of the right plastic opening tool underneath the magnet.
-
Wedge the left plastic opening tool underneath the magnet and simultaneously pry and push it towards the right plastic opening tool.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the previously described procedure to remove the smart cover magnet near the bottom left corner of the front panel assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pair of tweezers to carefully place the upper left smart cover magnet in place.
-
Repeat the procedure with the bottom left smart cover magnet.
-
다른 76명이 해당 안내서를 완성하였습니다.
댓글 8개
Does the screen they offer on this site come with the home button IC connector?
courtney m - 답글
when removing the LCD panel be very careful the screw hole tabs break really easy i broke the one next to the cable, but i was able to repair it with epoxy that i had .
Just wanted to say that this guide was great! It took me around three hours since the screen was extremely broken with tiny pieces of glass that had to get removed. Other than that, I had no issues thanks to the help from this guide. Thanks!