이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
-
냄비나 팬에 iOpener가 완전히 잠길 정도로 충분한 물을 채우세요.
-
물이 끓을 때까지 가열하세요. 불을 끄세요.
-
iOpener를 뜨거운 물에 2~3분간 담그세요. iOpener가 물에 완전히 잠겼는지 확인합니다.
-
집게를 사용하여 뜨거운 물에서 가열된 아이오페너를 꺼내세요.
-
수건으로 iOpener를 완전히 말리세요.
-
iOpener를 사용할 준비가 되었습니다! iOpener를 재가열해야 한다면 물을 끓인 후 불을 끄고 2~3분 동안 iOpener를 물에 담가 두세요.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.
-
Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully place a suction cup halfway up the heated side.
-
Be sure the cup is completely flat on the screen to get a tight seal.
-
While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.
-
Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat and reapply the iOpener.
-
Let it rest for a few minutes to reheat the left edge of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue moving the opening pick down the side of the display to release the adhesive.
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Take the first pick you inserted and slide it up toward the top corner of the iPad.
-
If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opening pick around the top left corner of the iPad to separate the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the opening pick in the iPad slightly past the front-facing camera.
-
Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
-
Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the top right opening pick around the corner to fully release the top edge of the glass.
-
Leave this pick in place to keep the adhesive from re-sealing itself, and grab a new pick for the next step.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to slide the pick down the right edge of the iPad, releasing the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Leave the opening picks in place and reheat the iOpener.
-
Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the lower left pick to the lower left corner to cut the adhesive on that corner.
-
Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.
-
Antennas
-
Home button cavity
-
Digitizer cable
-
The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
With a new pick, slice gently over the left-hand antenna, stopping before the home button.
-
Leave the pick in place before moving on.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.
-
Insert the pick slightly deeper and work it back toward the home button.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift slowly and gently to further detach the adhesive along the lower edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
The front-facing camera housing may stick to the front panel; peel up the housing and place it back over the camera to protect it.
-
Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.
-
Return the front-facing camera housing to its recess in the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use tweezers to peel up and remove the rectangular piece of foam tape covering the top right LCD screw.
-
Remove the triangular tape covering the lower right LCD screw.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If the tape is present, use the flat end of a spudger to pry the tape up and away, exposing the LCD screw beneath.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the four 3.9 mm Phillips #000 screws securing the LCD to the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pair of tweezers to peel up the small piece of tape connecting the LCD frame to the right speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pair of thin tweezers to pull up the top of the foam tape surrounding the LCD.
-
Use the tweezers to peel the foam tape up to expose the top of the LCD.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the tip of a spudger between the LCD frame and the tape on the top of the LCD.
-
Slide the spudger along the space between the LCD frame and tape, separating the tape from the LCD frame.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a guitar pick into the gap between the LCD and rear case, near the top of the left side of the LCD.
-
Bend the pick slightly away from the iPad, just enough to spread the gap between the LCD and rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the guitar pick into three more locations down the left side of the LCD and bend it over in each location, to slide the LCD over to the right side of the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Now switch to the right side of the LCD, and pry with the guitar pick in several places along the side to shift the LCD back to the left.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the flat end of a spudger between the LCD frame and the metal backing plate.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Starting at the top right of the device, slide the spudger in between the LCD frame and metal backing plate, which will separate the adhesive as you push.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Repeat the previous procedure along the top of the LCD.
-
Insert the flat end of the spudger between the LCD frame and metal backing plate and gently push the spudger in across the top of the device, separating adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue with the left side of the LCD: insert the flat end of the spudger between the LCD and shield plate and insert the spudger as far as it will go.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the LCD up a couple inches from the rear case to ensure it's free from the adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding the LCD with one hand, Insert the flat end of a spudger into the gap between this tape and the left speaker.
-
Gently pull the LCD away from the speakers while rotating the spudger outward to separate the tape from the speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the flat end of the spudger into the gap between the right speaker and the LCD tape.
-
While pulling the LCD away from the speakers, rotate the spudger outward, widening the gap and releasing the tape from the speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following screws securing the LCD shield plate to the rear case of the iPad:
-
Two 2.6 mm Phillips #00
-
Thirteen 1.7 mm Phillips #00
-
One additional 1.7 mm Phillips #00 on some devices.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the flat end of a spudger underneath the center of the LCD shield plate from the bottom end of the iPad.
-
Pry up on the spudger to free the plate from the sides of the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three 1.3 mm Phillips #00 screws securing the connector shield to the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pair of tweezers to grasp and remove the connector shield from the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a plastic opening tool to pry the LCD connector from its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding the LCD with one hand, insert the flat end of a spudger between the LCD and tape on the iPad's right side.
-
Slide the spudger outward, separating the tape, while gently lifting up on the LCD to pull it away from the tape.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While still holding the LCD up with one hand, move on to the iPad's left side and repeat the previous step's procedure to separate the second piece of tape.
-
Insert the flat end of a spudger between the LCD frame and tape, and slide outward while gently lifting up on the LCD.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
To minimize stress on the socket, try prying under the short edge of the connector, rather than the long edge which is shown in these images.
-
Gently pry the digitizer connector up from its socket on the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to peel back the small piece of tape covering both antenna cables located near the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
With the tip of a spudger, peel up the larger piece of tape covering both antenna cables near the bottom of the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following three screws securing the bottom left antenna to the rear case:
-
One 1.2 mm Phillips #00
-
One 1.1 mm Phillips #00
-
One 2.5 mm Phillips #00
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to loosen the foam adhesive securing the Wi-Fi antenna to the left speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to fold the left-hand wide piece of tape away from the left speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the wide tape toward the top of the iPad, applying constant force to release it from the antenna cable between it and the speaker.
-
Slide the tip of a spudger through the gap between the wide tape and the antenna cable, to break the adhesive connecting the two.
-
Continue pulling the wide tape until it is no longer covering the antenna cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
The right-hand wide piece of tape covers the antenna cable in the same way as the left.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the wide tape toward the top of the iPad, applying constant force to release it from the antenna cable between it and the speaker.
-
Slide the tip of a spudger through the gap between the wide tape and the antenna cable, to release the adhesive connecting the two.
-
Continue pulling the wide tape until it is no longer covering the antenna cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.
-
Gently pull the antenna cable out of the way as you work along the piece of tape, to keep it from resealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of the spudger to pry the antenna cable tape up from behind the right speaker as well.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to remove the small piece of tape securing the antenna cable in the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to pry the small metal retaining clip off the antenna cable.
-
De-route the antenna cable from the clip.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 1.4 mm Phillips #00 screw securing the left speaker to the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert the tip of a spudger into the gap between the left speaker and the bottom left side of the rear case.
-
Pry around the bottom of the speaker, sliding it out from its recess in the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Once enough of the speaker is exposed, grasp it and pull it away from the rear case.
-
Remove the left speaker from the iPad.
-
다른 2명이 해당 안내서를 완성하였습니다.