주요 콘텐츠로 건너뛰기

Mac용 Logitech MX Master 3 마우스 피트(나사를 덮는) 분리

알림: 귀하는 선행 작업 안내서를 편집하고 계십니다. 변경된 사항들은 이 선행 작업 단계를 포함하는 안내서 11개에 영향을 미칩니다.

1 단계 번역중

1 단계
Logitech MX Master 3 for Mac Mouse Feet (That Cover Screws) Removal, Soften the mouse feet adhesive: 0 단계, 이미지 3개 중 1개 Logitech MX Master 3 for Mac Mouse Feet (That Cover Screws) Removal, Soften the mouse feet adhesive: 0 단계, 이미지 3개 중 2개 Logitech MX Master 3 for Mac Mouse Feet (That Cover Screws) Removal, Soften the mouse feet adhesive: 0 단계, 이미지 3개 중 3개
Soften the mouse feet adhesive
  • Flip the mouse's power switch into the OFF position, unplug any cables, and flip it over so the feet are facing up.

  • The unique shape of some mice can prevent them from laying flat. If you need to, lay your mouse on a soft towel to prevent wobble.

  • If you're planning to reuse your existing mouse feet, note that the adhesive needs to be thoroughly heated for them to be cleanly removed.

  • Heat an iOpener and apply it to each of the mouse feet for about one minute each.

  • Alternatively, you can use a hair dryer to soften the mouse feet adhesive.

  • When using a hair dryer, don't heat the feet for more than a couple seconds at a time—anything hotter than just warm to the touch risks melting or warping the plastic lower case.

  • The information sticker adhesive may soften during this step, but you don't need to remove it.

마우스의 전원 스위치를 OFF/끄기 위치로 돌리고 케이블을 모두 연결 해제한 다음 피트가 위를 향하도록 뒤집으세요.

일부 마우스는 독특한 모양으로 인해 평평하게 놓지 못할 수 있습니다. 필요한 경우 마우스가 흔들리지 않도록 부드러운 수건 위에 올려놓으세요.

기존 마우스 피트를 재사용할 계획이라면 접착제를 완전히 가열해야 깨끗하게 제거할 수 있다는 점에 유의하세요.

각 마우스 피트에 약 1분 동안 iOpener를 가열하여 대세요.

대안으로 헤어 드라이어를 사용하여 마우스 피트 접착제를 부드럽게 만들 수 있습니다.

헤어 드라이어를 사용할 때는 한 번에 2초 이상 가열하지 마세요. 만졌을 때 따뜻할 정도보다 더 뜨거우면 플라스틱 하단 케이스가 녹거나 뒤틀릴 위험이 있습니다.

이 단계에서 정보 스티커 접착제가 부드러워질 수 있지만 분리할 필요는 없습니다.

귀하의 기여는 오픈 소스 Createive Commons 라이선스 하에 허가되었습니다.