주요 콘텐츠로 건너뛰기

Google Pixel 8 Pro スクリーンの交換

알림: 귀하는 선행 작업 안내서를 편집하고 계십니다. 변경된 사항들은 이 선행 작업 단계를 포함하는 안내서 14개에 영향을 미칩니다.

21 단계 번역중

21 단계
Google Pixel 8 Pro Screen Replacement, Reassembly information: 0 단계, 이미지 3개 중 1개 Google Pixel 8 Pro Screen Replacement, Reassembly information: 0 단계, 이미지 3개 중 2개 Google Pixel 8 Pro Screen Replacement, Reassembly information: 0 단계, 이미지 3개 중 3개
Reassembly information
  • If you're installing a new screen with pre-installed adhesive, follow this step during reassembly. Otherwise, follow this guide to apply adhesive to your old screen.

  • Thoroughly check the entire screen for any plastic liners or tape and use the pull tabs to remove all of them. Look carefully for a large piece of plastic covering the back of the screen, a small one near the front camera cutout, and adhesive liners around the perimeter.

  • Reconnect the screen cable and reinstall its cover.

  • This is a good point to test your phone before sealing it up. Temporarily power on your phone and make sure it works as expected. Power it down before continuing.

  • Firmly press the screen into place on the frame—you should feel the clips "pop" into place.

  • Press firmly around the perimeter of the screen to secure it with the new adhesive.

  • Optionally, you can strengthen the adhesive bond by applying pressure evenly to the phone.

  • Follow this guide to calibrate the fingerprint sensor.

取り付ける新しいスクリーンに予め両面テープが貼り付けられている場合は、この手順に沿って作業を続けて下さい。スクリーンに両面テープが貼られていない場合は、こちらのガイドに従ってスクリーンに両面テープを貼って下さい。

プラスチックの剥離紙やテープ類がどこにあるか、スクリーン全体について確認してから、このタブを使ってそれらを全て取り除いて下さい。スクリーンの背面を覆う大きなプラスチック片やフロントカメラの切り欠きの近くにある小さなもの、及び縁周辺の接着剤の剥離紙は特に注意して確認して下さい。

スクリーンケーブルを接続し直して、スクリーンケーブルカバーも取り付け直して下さい。

スクリーンを接着する前に正しく機能するかどうか確認するなら、この時点で行いましょう。一時的に電源を入れ、正常に動作するか確認しましょう。組み立てを再開する前に、必ず電源を切りましょう。

スクリーンを筐体の正しい位置に合わせてからしっかり押し付けて下さい。クリップが正しい位置に収まる「ポンッ」という感触を感じるはずです。

スクリーンの端周辺をしっかり押し付けて、新しい両面テープをしっかり貼り付けます。

スクリーンをよりしっかり接着するためにデバイスの縁を均等に押さえつけることもできます。

こちらのガイドに従って指紋センサーのキャリブレーションを行って下さい。

귀하의 기여는 오픈 소스 Createive Commons 라이선스 하에 허가되었습니다.