기기를 수리하세요

수리할 권리

상점

알림: 귀하는 선행 작업 안내서를 편집하고 계십니다. 변경된 사항들은 이 선행 작업 단계를 포함하는 안내서 25개에 영향을 미칩니다.

안내서로 돌아가기
영어
중국어
다음 단계

1 단계 번역 중

1 단계
Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive. If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.

  • Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

  • If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.

  • Lay the heated iOpener over the rear panel for about two minutes to loosen the adhesive around the edge of the glass.

  • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

  • Shift the iOpener to heat the remaining section of the panel for another two minutes.

  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

将你的手机正面朝下放置。

如果手机的玻璃面板已经碎裂，请在拆卸过程中用胶带固定住整个面板。

将iOpener放置在面板上约60秒以融化固定玻璃面板边缘的封胶。

移动iOpener以加热剩余部分的面板，同样需要60秒。

吹风机，热风枪，或者加热工具也许都会用到，但是千万不要过度加热手机——OLED 屏幕和内部电池都会容易热损坏。

[* icon_note] Place theOpening your phone facedownwill compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.
[* icon_note] Place theOpening your phone facedownwill compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.
[* icon_note] If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.
[* black] Lay the heated iOpener over the rear panel for about 60 secondstwo minutes to loosen the adhesive around the edge of the glass.
[* icon_note] You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.
[* black] Shift the iOpener to heat the remaining section of the panel for another 60 secondstwo minutes.
[* black] Lay the heated iOpener over the rear panel for about 60 secondstwo minutes to loosen the adhesive around the edge of the glass.
[* icon_note] You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.
[* black] Shift the iOpener to heat the remaining section of the panel for another 60 secondstwo minutes.
[* icon_caution] A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

귀하의 기여는 오픈 소스 Creative Commons 인가 하에 허가되었습니다.