기기를 수리하세요 커뮤니티 상점

2012년 9월 12일에 발표된 여섯 번째 Apple iPhone입니다. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 16, 32, 또는 64GB / 검정색 또는 흰색으로 제공하였습니다.

2522 질문 전체 보기

옵션

No Service after repair! :( Might have broken a component.

The phone worked fine before I did the repair, but I believe I may have broken a component on the board with a screwdriver. Can someone tell me if this component in the photo is related to cell reception? And which components I should look at to determine if they may be damaged?

And is there is an easy way I can go about fixing it?

Thank you to anyone that might offer suggestions.

http://www.imgur.com/Mo3Z6T0

Block Image

EDIT: Now I found another component that appears damaged, couldn't his one be the culprit?

http://m.imgur.com/SWMfwOh

Block Image

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요
점수 2
댓글 1개

My 5s fall down display broken .. I replaced display but showing no service. What is the compliant. Which part become complaint

의

댓글 달기

답변 4개

필터:
가장 유용함 가장 최근 가장 오래된
선택된 답변

옵션

Cameron,the first image shows C201 missing. That is a 56PF 6.3V 5% capacitor in a 01005 package. It is part of your CG flex connector circuit. The second image shows C242 missing. Coincidentally enough, that capacitor has identical values and is part of your headphone detect circuit. Neither one of those is directly related to your reception circuit. As for fixing it, sorry no easy fix. Those components are rather small and require special tools and skills to be replaced. Hope this helps, good luck.

해당 답변은 도움이 되었습니까?

예 아니요
점수 4
댓글 달기

옵션

My only question would be did you try turning the phone on again? like does it still work? I am curious because its hard to tell from the photos what your indicating.

해당 답변은 도움이 되었습니까?

예 아니요
점수 0

댓글 2개:

Yes it works fine.. Everything works on the phone except for the reception. But I cannot figure out why.. I have already replaced all components related to the cellular antenna (like the lightning connector assembly) and screws holding antenna to the frame.

의

Can you detail all you have done or upload a little bit clearer pictures? I apologize my eyesight is horrible. It looks like you may have broken it but i would need a clearer or bigger picture to be absolutely sure.

의

댓글 달기

옵션

You should carefully clean all the connectors and make shure that tey are well clipped. It happened to me on an iPhone4. The + volume button was the only one that was not working, so ... check and clean conections !

Second option ont he same iPhone 4 after a screan change the repair man had to connect and disconnect the iphone to itunes (or maybe a special soft) to make the service back again. He was aware about this sublety and make the service work just after the repair

해당 답변은 도움이 되었습니까?

예 아니요
점수 0
댓글 달기

옵션

usually they are resisters and its hard to determine the resistance. a alternative would be to jump add a jumper.

use flux and a soldier iron and some vary little solder and bridge the connection.

be sure to disconnect power and remove battery from area were you will be applying heat.

always remember to take your time.

해당 답변은 도움이 되었습니까?

예 아니요
점수 -1
댓글 달기

귀하의 답변을 추가하세요

Cameron 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 3

전체 시간: 9,371