주요 콘텐츠로 건너뛰기

6s와 유사한 하드웨어 사양의 4-inch iPhone은 2016년 3월에 출시되었습니다. 16/64GB 저장 옵션 및 은색, 스페이스 그레이, 금색 또는 로즈 골드로 제공됩니다. 모델 A1662 및 A1723.

1049 질문 전체 보기

Why won't my screen respond properly?

I recently had to replace my LCD and Digitizer after I broke the screen. I've gone through 4 screens now, 2 of them were from a cheap place and while the digitizer portion worked 100% the LCD was distorted so I ended up returning both of them and got a screen from iFixit, this time while the LCD was crystal clear the touch function was acting up a bit. As in it didn't respond to the tips of my fingers, just the centers, unless I pushed down very hard or slid my finger from the center to the tip. After explaining the issue another screen was sent out to me. After plugging this one in it seems to be doing the same thing, though, not as bad. It now responds to the tip of my thumb but no other finger tips seem to work, this makes it quite hard to type, it also seems to not respond to tapping as well, I sometimes have to tap multiple times for it to register correctly. I tried all the suggestions, cleaning the contacts and restoring my phone and reseating connectors to no avail. I was playing with it earlier and while I had the screen pulled away from the back of the phone it was working correctly for a bit but once I had placed it back into the phone, it reverted back to the way it was acting before. I don't see any damage in the cable ribbons or the connectors themself. I know its not the phone because like I said before the cheaper screens work perfectly for their touch parts. Any ideas?

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 1
댓글 달기

답변 1개

선택된 답변

Hi Tyler. Normally, a defective replacement screen assembly would be the normal diagnostic. However, having gone through four different ones, it gets harder to say it with the same conviction. Do you have access to another iPhone 5S or SE where you could try to isolate some parts. You really need to know if these screens work or perhaps use a known-good screen in your DUT.

You may also have an issue with the way the screen assembly is seating in the housing. You said it worked ok when the screen was not in the housing. Try removing the logic board and connecting just a battery (known-good, from your stock), Lightning Connector (again, known-good, from your stock) and your screen assemblies for test.

Try to eliminate as many variables as possible. You may ultimately have a logic board issue of the screen cracked due to a heavy impact.

해당 답변은 도움이 되었습니까?

점수 3

댓글 1개:

Thanks for the reply! Unfortunately I don't have any spare phones or parts to test the way you mentioned. I also want to add that I forgot to mention the two screens I've got from ifixit were the complete front displays, I bought just the digitizer and LCD screen as my initial replacement and it worked perfect but I ended up putting a screw in the wrong place and trashed it. It's seeming to be a defective screen as much as I really didn't want to admit it and have to buy another screen, but I do believe since the other screens I've tried had their touch functions working as normal that it's not a problem with the phone itself, not to rule out your theory or anything. Sorry for any errors in my response I'm typing from a half working phone!

댓글 달기

귀하의 답변을 추가하세요

Tyler McEwan 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 1

전체 시간: 121