기기를 수리하세요 커뮤니티 상점

Apple iPhone 5s는 2013년 9월 10일에 발표되었습니다. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 16, 32, 또는 64GB / 은색, 금색 및 스페이스 그레이.

3530 질문 전체 보기

옵션

current draw fluctuating when power button pressed

Hi , i have an iphone 5s which had a charging issue , i changed the U2 and it was working fine i charged battery fully and phone was ok .

I replaced the shields ,put the phone back together and it didnt work .

took it apart again and found U1600 looked a bit damaged , i thought i was careful but maybe i caught it when replacing the shields , anyway i have changed U1600 but still the same .

when connected to dc power the amps fluctuate (see this video)

5S no boot

What does this indicate . ?

I have checked PP_BATT_VCC_CONN and its good 3.8 V

I thought on the schematic it listed the critical voltage lines but i cant seem to find them .

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요
점수 0
댓글 달기

답변 3개

필터:
가장 유용함 가장 최근 가장 오래된
선택된 답변

옵션

Does the logic board still work without the shields? If so, I would add only one shield at a time and test. Then repeat if successful until you find which shield is causing the problem.

UPDATE (2017/05/02)

Just to recap, replacing U2 solved your charging problem but when you soldered the shields back on it failed to boot. Removing the shields didn't help and you then replaced U1600 because it looked damaged. Now the phone doesn't boot and the current draw fluctuates.

Does iTunes recognize your phone is connected? If not, then this still looks like a U2 (Tristar) problem. I don't know how experienced you are at micro-soldering so I'll suggest (no offence intended) that perhaps you may have applied too much heat when you put the shields back on. Let me know if I am concerned about this for nothing :>).

I would go back and test the main lines (BATT_VCC, VCC_MAIN, PP5V0_USB) as well as all of the voltage rails created by the PMIC (U7). I would also closely inspect the Tristar/PMIC/U1600 area for any (partially) dislodged components or solder bridges near the shield anchor points.

해당 답변은 도움이 되었습니까?

예 아니요
점수 2

댓글 6개:

No, shields are all off .

의

Hi ,sorry for the delay on answering , i Finally! , found some time to spend on this board , , yes thats correct the phone booted up fine and charged . I tunes does not see it when plugged in .

I put the shields back on by just touching the solder points with the iron tip , i thought maybe i pressed down a bit hard to get the solder points to line up (breaking the U1600).

I had a good look around the board for dislodged components as you suggested and found R78 was dislodged so i put that back on and was kind of hopeful but still same fault ,

i checked the voltage on PP_BATT_VCC :

These are all the components on that line , do i need to test voltage at all the components on a line to check a line ?

L4 3.8V

C332 3.8V

C333 3.8V

C337 3.8V

C3337 3.8V

C335 3.8V

C48_RF 3.8V

C42_RF 3.8V

C44_RF 3.8V

C43_RF 3.8V

C45_RF 3.8V

C51_RF 3.8V

C47_RF 3.8V

C46_RF 3.8V

C49_RF 3.8V

C1214_RF 3.8V

C100_RF 3.8V

C1201_RF 3.8V

C229_RF 3.8V

R32_RF 3.8V

C184_RF 3.8V

C118_RF 3.8V

C148_RF 3.8V

C242_RF 3.8V

C154_RF 3.8V

L5 3.8V

C387 3.8V

의

C386 3.8V

....

PP3V0_ACC is there and PP5V0_USB_PROT

the voltage on these lines fluctuate on and off with the amp draw on the psu .

의

Am i right in thinking pin E21 of U7 should have 3.3v , i have no volts on R131 .

의

You only need to check one component on a rail to get the right measurement. As for the TRISTAR_TO_PMU_USB_BRICKID line (R131) it should be 5.25V but I don't know under what conditions it will give that voltage.

If iTunes doesn't recognize your device, then it sounds to me like the Tristar replacement was not successful.

의

댓글 1개 더보기

댓글 달기

옵션

Hi ,sorry for the delay on answering , i Finally! , found some time to spend on this board , , yes thats correct the phone booted up fine and charged . I tunes does not see it when plugged in .

I put the shields back on by just touching the solder points with the iron tip , i thought maybe i pressed down a bit hard to get the solder points to line up (breaking the U1600).

I had a good look around the board for dislodged components as you suggested and found R78 was dislodged so i put that back on and was kind of hopeful but still same fault ,

i checked the voltage on PP_BATT_VCC :

These are all the components on that line , do i need to test voltage at all the components on a line to check a line ?

.

L4 3.8V

C332 3.8V

C333 3.8V

C337 3.8V

C3337 3.8V

C335 3.8V

C48_RF 3.8V

C42_RF 3.8V

C44_RF 3.8V

C43_RF 3.8V

C45_RF 3.8V

C51_RF 3.8V

C47_RF 3.8V

C46_RF 3.8V

C49_RF 3.8V

C1214_RF 3.8V

C100_RF 3.8V

C1201_RF 3.8V

C229_RF 3.8V

R32_RF 3.8V

C184_RF 3.8V

C118_RF 3.8V

C148_RF 3.8V

C242_RF 3.8V

C154_RF 3.8V

L5 3.8V

C387 3.8V

C386 3.8V

....

PP3V0_ACC is there and PP5V0_USB_PROT

the voltage on these lines fluctuate on and off with the amp draw on the psu .

해당 답변은 도움이 되었습니까?

예 아니요
점수 0
댓글 달기

옵션

Hi,i have the same issue,i think when you tried o put back the shield you use too much temp and CPU ball’s gone away!maybe you need to reball the CPU.sorry for bad english

해당 답변은 도움이 되었습니까?

예 아니요
점수 0
댓글 달기

귀하의 답변을 추가하세요

markparnell1972 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 3

전체 시간: 1,073