Home button works fine but Touch ID doesn't

Question

iPhone SE

6s와 유사한 하드웨어 사양의 4-inch iPhone은 2016년 3월에 출시되었습니다. 16/64GB 저장 옵션 및 은색, 스페이스 그레이, 금색 또는 로즈 골드로 제공됩니다. 모델 A1662 및 A1723.

1049 질문 전체 보기

ricardo.wj @ricardowj

평판: 1

게시일: 2017년 10월 13일

옵션

Home button works fine but Touch ID doesn't

hey everyone,

So, as the title says, the home button of my iPhone SE is working fine, but the Touch ID isn't, as it says "Unable to activate touch ID in this phone, try again later".

Things I tried to do:

- Tested Touch ID on ios 10;

- Tested Touch ID on ios 11;

- Reconnected Home button cable;

- Hard reset.

I tried all that, but it still doens't work. I think this's weird, because the home button is working fine.

I think there's no solution but it's worth the try. the device got repaired on board (IC U2 & FL 2400 component).

Thanks,

Ricardo

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

예 아니요

점수 0

댓글 달기

답변 2개

선택된 답변

Minho @refectio

평판: 221.5k

15

290

807

게시일: 2017년 10월 13일

옵션

Take a close look at the flex cable on the button, preferably with magnification. Look for any damage or tear, no matter how tiny. I would also closely inspect the connector on the flex and on the dock flex as well.

The U2 repair shouldn't directly impact it unless the flexes were slightly damaged upon re-assembly.

해당 답변은 도움이 되었습니까?

예 아니요

점수 2

댓글 1개:

Hey,

I have seen with attention the whole flex cable and all the connectors, but I didnt see any damage. I dont have any microscope at the moment, so im a bit limited. Dont know what else can I do.

ricardo.wj 의 2017년 10월 13일

댓글 달기

Hey,

I have seen with attention the whole flex cable and all the connectors, but I didnt see any damage. I dont have any microscope at the moment, so im a bit limited. Dont know what else can I do. — ricardo.wj

Rachel Acosta @alphapeaches 평판: 2k 6 4 4 · Answer 1 · 2017-10-13T03:29:38-07:00

Rachel Acosta @alphapeaches

평판: 2k

6

4

게시일: 2017년 10월 13일

옵션

I have that message with my 5s, but it's because I replaced the home button. It works the same with the SE, the home button and the board have to match for Touch ID to work.

Repairing the IC component shouldn't have affected anything. Here's an article that discusses it as a solution for Touch Disease (6/6+), with no mention of affecting the home button or Touch ID, so I doubt the board work would have caused the issue. Even on a 6, the home button and logic board need to match for Touch ID to work.

My suspicion is that it's actually a new home button. I'm not sure what else would cause that.

해당 답변은 도움이 되었습니까?

예 아니요

점수 0

댓글 1개:

Hey,

Sorry. Forgot to mention, the home button is the original that came in with the iPhone.

Thanks

ricardo.wj 의 2017년 10월 13일

댓글 달기

iPhone SE

Home button works fine but Touch ID doesn't

답변 2개

귀하의 답변을 추가하세요