주요 콘텐츠로 건너뛰기

2015년 9월 25일 출시. Model A1687/A1634. 수리는 이전 모델과 유사하며 스크류 드라이버 및 비집는 도구가 필요합니다. GSM 또는 CDMA / 6, 64, 또는 128GB / 은색, 금색, 스페이스 그레이 및 로즈 골드로 제공하였습니다.

1041 질문 전체 보기

Black screen on wake up but backlight is ok

Hello

I get an Iphone 6S plus with what I thought was a backlight trouble.

Iphone was correctly seen by itunes but no image on Screen. In fact at startup the screen was completely black even using a strong light. The phone correctly responds to power button, mute button but the touch screen was not active (I couldn't accept the connection with my Mac in Itunes and no way to slide to turn it off ).

I managed to restore it completely and it was still black. But when I reset it using power and home button, the phone waked up and was fully functional except a minor trouble , the SIRI mic was not working. I charged the phone all night long and it seems ok. When I decided to clean the microphone on top of screen to see if i can save it. After this, blank screen again.

Note: after some bad history with 6s I know that I have to remove battery before any screen connexion.

I proceed to a new restore and when again the phone was ok.

Now sometime when the phone goes in sleep mode (after 30s of no use) i can't wake it up. I need to proceed to a soft reset, and phone is back again.

During the 'black' session, the touch screen seems no active.

What could make such strange behavior ?

note: Screen is not a genuine, I didn't tried yet to change it

note: Motherboard seems ok, no water damaged indicator

Note: one time after a reset the battery was described as empty (red battery logo and request for connexion) but it was charged at 60 % (it was just after I replug it)

Note: sometime when i press the power button , the screen stays dark a few seconds then get brighter and brighter until it normal. as a capacitor was charging..

Any help is welcome.

답변되었습니다! 답변 보기 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 0
댓글 3개

was it updated as the new ios update does seem to mess about with oem lcds etc, try downgrading the ios to see if that helps

Thank you daniel, but the trouble was there before I upgrade to ios 11.0.3 (that version solves issues with oem lds). And We can't go back to ios 10 now.

Hi

Just a short feed back. With a new screen (refurbish) every thing is fine !!!

>Thanks to Minho

댓글 달기

답변 1개

선택된 답변

I would certainly try an original quality LCD as a first step. The Touch controller is on the screen as opposed to the logic board so if that is causing any issues, only a replacement screen can solve it. If a known-good screen doesn't help, then I suspect that the problem is with the Chestnut circuit (U4000). It supplies the voltages for the LCD and Touch. Next time you open up the phone, also inspect the connectors to insure there is no debris or broken pins.

해당 답변은 도움이 되었습니까?

점수 1

댓글 1개:

New screen is on its way to me. I hope it is only the screen. I don't like microsoldering guy :) : ) thank you for your help

댓글 달기

귀하의 답변을 추가하세요

philippe 님은 대단히 고마워 할 것입니다.
조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 5

전체 시간: 5,307