DV365
Model: DV365ETBGSF/A1
Bulletins:
| Rigid | Metallic Flexible' | Rigid | Metallic Flexible' |
|---|---|---|---|
| 124 m (41 f) | |||
| 11.2m(37 f.) | |||
| 10.1 m (33 f) | |||
| 6.5m (21 tt) |
Table Caption: This table presents a comparison of lengths, showing four measurements for "Rigid" and four for "Metallic Flexible," with some entries being empty.
Support Information:
HELP: 1-888-751-4086 (Tech Sup. - ASC/SSD)
1-866-894-0637 (Tech Sup. - FE/ME)
GSPN: http://gspn3.samsungcsportal.com/main.jsp
PLUS ONE: http://my.plus1solutions.net/clientPortals/samsung
Dryer Q&A
| Q. What does it mean when chasing light appear in the display? | A. The chasing lights appear in the display when Wrinkle Prevent is selected. This lets you know that the dryer is tumbling intermittently for 95 minutes with room temperature air after the cycle is complete to reducing wrinkling. The load is dry and can be removed at any time during Wrinkle Prevent. |
|---|---|
| Q. Whyis the estimated drying time so long? | A. The initial estimated drying time will be longer because the dryer has not yet detected the amount of moisture in the load. After the dryer has been running for several minutes, a more accurate estimate will be displayed. Remember, the times are estimated. The actual drying time may be longer or shorter, depending on the load. |
| Q. My dryer seems to run longer than I expect. Why? | A. The dryer automatically senses the dryness level of load. Be careful to avoid overloading your dryer. For best drying results, avoid mixing heavy and lightweight items in the same load. |
| Q. My dryer has an unpleasant Odor | A. The lint trap has not been cleaned. If the lint trap is not cleaned it can block moisture from escaping from the drum and the air inside is recycled, through the old lint. This concept also applies to lint clogging the exhaust duct. Both conditions can also lead to moisture being trapped in the drum, which will prevent the dryer from drying clothes completely. B. The clothes from the washing machine were sitting in the washing machine for too long and started to mildew or sour, or there was an odor from the washing machine. When sour clothes are first pulled out of the washing machine , the smell may be less noticeable. However, once heat is applied , the smell is intensified. C. A small animal ( birds, Mice ,lizards, etc ) has climbed into the exhaust vent. Small animals are drawn to the exhaust vent because of the warmth. It is very important to cover this vent with a laundry exhaust vent cover. |
Table Caption: This table provides troubleshooting tips and explanations for common dryer issues, including the meaning of chasing lights, long drying times, and unpleasant odors.
Clogged Vent
- Clogged vents will prevent the clothes from drying properly
- Make sure the vent is clear of debris and lint build-up
Fast Track Troubleshooting
IMPORTANT SAFETY NOTICE -'For Technicians Only' This service data sheet is intended for use by persons having electrical, electronic, and mechanical experience and knowledge at a level generally considered acceptable in the appliance repair trade. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet.
Publication # Dr DV365** Production Date 05/06/14
Error Codes
| Error Display LED | Trigger | Action Taken |
|---|---|---|
| The Thermistor resistance is very low or high | tS Clogged lint screen | |
| Restricted vent system_ Check Thermistor resistance | ||
| do | Running the dryer with door open | Check for Close the door, and run the dryer Loose or open wire terminals at the Door sensor circuit. |
| dF | Invalid state for more than 0.25 seconds | Check for Loose or open wire terminals at the Door sensor circuit. |
| bE | Invalid state of key circuit short for 75secs | Check for If the display PCB key circuit is shorted or not |
| od | Invalid time in excess Dry time Dry7 | Check for Sensor bar Open |
| hE | Invalid heating Temp in running the dryer | Check for Restricted vent system |
| Et | Invalid state of EEprom communication | Check for PCB with EEprom circuit |
| FE | Invalid power source Frequency | Check for Not using regular power source frequency |
Table Caption: This table lists error codes displayed by a dryer, the conditions that trigger them, and the corresponding troubleshooting actions to take. It helps identify potential issues like sensor malfunctions, blocked vents, or electrical problems.
Reference Info
Belt Position
Troubleshooting
Checking the Motor
- 'Unplug the harness connector and the
