메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Akai MPK25 Keys Replacement

작성자 Will Saba (또 다른 기여자 5명)
  • 댓글 1
  • 즐겨찾기 2
  • 완료: 6

난이도

쉬움

단계

7

소요 시간

10 분

섹션

2

플래그

1

Featured Student Guide

추천 학생 안내서

해당 안내서는 저희 멋진 학생들의 노력으로 만들어졌으며 iFixit 직원들이 뛰어난 안내서로 판명하였습니다.

소개

Use this guide if any of the keys are broken, chipped, or stuck.

도구

해당 도구 구매

부품

  1. Remove all the selector knob covers by pulling them off.

    • Remove all the selector knob covers by pulling them off.

    편집

  2. Using needle nose pliers, remove the washers from the four corner selector knobs.

    • Using needle nose pliers, remove the washers from the four corner selector knobs.

    편집

  3. Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

    • Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

    편집

  5. Carefully flip the device to the front making sure you secure the face plate and the chassis together. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

    • Carefully flip the device to the front making sure you secure the face plate and the chassis together.

    • Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

    편집

  6. Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

    • Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys.

    • Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

    편집

  7. Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key. Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key.

    • Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key.

    편집

  8. Lift the key from the front of the keyboard towards the back in order to remove it completely.

    • Lift the key from the front of the keyboard towards the back in order to remove it completely.

    편집
결론

To reassemble the keyboard and close up the case, follow these instructions in reverse order.

다른 6명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 5명과 함께

Will Saba

회원 가입일: 2013년 01월 11일

352 평판

안내서 2개 작성하였습니다

배지: 10

배지 +7개 더

팀

Cal Poly, Team 20-6, Maness Winter 2013 Cal Poly, Team 20-6, Maness Winter 2013 회원

CPSU-MANESS-W13S20G6

5 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 3

지난 7일: 18

지난 30일: 78

전체 시간: 7,220