소개

This is a step-by-step guide showing how to remove the LCD/Digitizer combo from the IBM WorkPad c3. This is a fairly easy removal.

부품

부품은 필요하지 않습니다.

  1. Turn the device over so that the screen is facing down.
    • Turn the device over so that the screen is facing down.

    • In the next step the device will be heated, so the screen must be turned over to prevent heat damage to the LCD/Digitizer.

    댓글 쓰기

  2. Using a hair dryer, slowly heat the edges of the WorkPad.
    • Using a hair dryer, slowly heat the edges of the WorkPad.

    • Spend at least one minute heating each side of the device. This will melt the glue holding the case together, and allow it to be removed.

    • Be sure not to touch the device directly after heating as it will be extremely hot. Use a towel or oven mitt to grab it.

    댓글 쓰기

    • Use a plastic opening tool to pry the back case from the WorkPad.

    • If the rear cover is not coming off very easily, you probably need to reheat the case in order to sufficiently melt the glue.

    댓글 쓰기

    • Turn the device over, so that the screen is laying on a flat surface.

    댓글 쓰기

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • If the back case has already been removed, carefully place it on the WorkPad to protect the circuitry inside from the heat.

    • Using the hair dryer, slowly heat the edges of the device. Spend at least 1 minute on each side, thoroughly heating the case.

    • The LCD/Digitizer combo is very sensitive to heat, and can easily be ruined if it is directly exposed to the hair dryer. Verify that the screen is face down.

    댓글 쓰기

    • The device will be extremely hot. Use a towel or oven mitt to grab it.

    • Using the Plastic Opening Tools, take the front of the case off.

    • If the case is difficult to remove, try repeating step 2.

    • The power button at the top of the device will be loose once the front part of the case is removed.

    댓글 쓰기

    • Remove the yellow tape that is covering the battery connector

    댓글 쓰기

    • Using the tweezers, carefully disconnect the battery cable from the port

    댓글 쓰기

    • Using the plastic opening tools, lift the battery out of the case

    • The battery is secured with adhesive and it will take some effort to remove

    댓글 쓰기

    • Using the spudger lift the tabs holding the LCD/Digitizer combo cables to the WorkPad.

    댓글 쓰기

    • Using your thumb, press down gently on the back of the LCD.

    • The LCD will disconnect and fall out of the case, so be sure to have your hand waiting for it.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Emily Falkenstein

회원 가입일: 2010년 10월 05일

51 평판

안내서 5개 작성하였습니다

Cal Poly, Team 21-35, Regan Fall 2010 Cal Poly, Team 21-35, Regan Fall 2010 회원

CPSU-REGAN-F10S21G35

3 회원들

안내서 5개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 5

전체 시간: 1,551