기기를 수리하세요 커뮤니티 상점

General Electric Create Jason Wu Casing Disassembly

소개

This guide will show how to carefully remove the front and back plastic casing that surrounds the camera.

필요한 것

  1. General Electric Create Jason Wu Casing Disassembly, General Electric Create Jason Wu Casing Disassembly: 1 단계, 이미지 1/3 General Electric Create Jason Wu Casing Disassembly, General Electric Create Jason Wu Casing Disassembly: 1 단계, 이미지 2/3 General Electric Create Jason Wu Casing Disassembly, General Electric Create Jason Wu Casing Disassembly: 1 단계, 이미지 3/3

    • Begin by removing the 5 screws (located: 2 screws on either side and 1 screw on the bottom) using the PH000 head in the Precision Phillips Screwdriver.

    • These screws were missing in our example. These screws should have been small Phillips PH000 screws 1.5mm in length.

    • These screws are very small. To keep from losing any pieces, place all small metals on a magnetic project mat.

    편집

  2. General Electric Create Jason Wu Casing Disassembly: 2 단계, 이미지 1/2 General Electric Create Jason Wu Casing Disassembly: 2 단계, 이미지 2/2

    • After the screws are removed, pull the front casing up and away from the camera.

    • If the casing is difficult to remove, use a plastic opening tool to gently pry up on the front as shown.

    편집

  4. General Electric Create Jason Wu Casing Disassembly: 3 단계, 이미지 1/3 General Electric Create Jason Wu Casing Disassembly: 3 단계, 이미지 2/3 General Electric Create Jason Wu Casing Disassembly: 3 단계, 이미지 3/3

    • Using your hands or an opening tool, pry off the silver frame, taking special care at the top of the camera where the buttons are as it is a little harder to pry off.

    • If the back casing is loose from the camera body, it may be easier to perform step 4 first, then accomplish this step. Proceed as your unit allows.

    편집

  5. General Electric Create Jason Wu Casing Disassembly: 4 단계, 이미지 1/3 General Electric Create Jason Wu Casing Disassembly: 4 단계, 이미지 2/3 General Electric Create Jason Wu Casing Disassembly: 4 단계, 이미지 3/3

    • The last part of the casing to disconnect is the back that houses the LCD screen.

    • The screen is attached by a connection ribbon. Gently pull the casing and screen away from the camera body to disconnect the casing.

    • The LCD screen is held onto the back casing by a small amount of adhesive. This may come loose during this process. Do not worry if they become separated.

    • This plug and the connection ribbon are fragile, try not to tear the connection ribbon when disconnecting.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Kylan Hennessy

회원 가입일: 01/23/17

573 평판

안내서 5개 작성하였습니다

배지: 15

배지 +12개 더

팀

Eastern Washington University, Team 2-6, Crane Winter 2017 Eastern Washington University, Team 2-6, Crane Winter 2017 회원

EWU-CRANE-W17S2G6

4 회원들

안내서 7개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 1

전체 시간: 198