이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
With the case closed, place the Mini 1000 top-side down on a flat surface.
-
Push both of the battery release latches toward each other.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the battery out of the Mini 1000 from the edge closest to the release latches.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following two screws:
-
One 6 mm Phillips screw
-
One 4 mm Phillips screw
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you.
-
Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.
-
Pull the cable out of its socket and remove the keyboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket.
-
Pull the SIM card ribbon cable out of its socket and peel it off the top of the hard drive enclosure.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Using the sharp tip of a spudger, pry and remove the four plastic screw covers from the underside of the HP Mini 1000.
-
The two bottom covers are short in height and are notched to prevent incorrect insertion
-
The upper right cover is taller in height and is notched.
-
The upper left cover is taller in height and is not notched.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the four 7 mm Phillips screws that secure the upper case to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Flip the computer over and open the display.
-
Remove the two 4.5 mm Phillips screws securing the upper case to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Wedge the flat end of a spudger in between the upper case and lower case near the bottom right corner of the display.
-
Carefully pry and rock the spudger upwards to create a small gap between the upper case and lower case.
-
Continue the previously described motion along the right edge of the upper case to release the clips securing the upper case to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Repeat the same procedure as mentioned in the previous step to release the clips along the left side of the upper case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the upper case and carefully lift it slightly upwards, freeing it from any remaining clips.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use your fingernail or the flat end of a spudger to flip up the retaining flap on the TouchPad cable ZIF socket.
-
Pull the TouchPad ribbon cable out of its socket.
-
Remove the upper case from the HP Mini 1000.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 3 mm Phillips screw securing Wi-Fi board to the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the Wi-Fi board and lift it straight away from its socket on the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 2.5 mm Phillips screws securing the heat sink to the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully lift the heat sink off the face of the motherboard and de-route the curved section from next to the fan.
-
Before reinstalling the heat sink, be sure to apply a new layer of thermal paste to the CPU. We have a thermal paste guide that makes it easy.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to pry both antenna connectors up from their sockets on the Wi-Fi board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to disconnect each of the following connectors from their respective sockets:
-
Speaker cable
-
Microphone cable
-
Fan cable
-
Power cable
-
Display data cable
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 5 mm Phillips screw securing the right display hinge to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 5 mm Phillips screws securing the left display hinge to the lower case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the display out of the lower case, minding any cables that may get caught.
-
다른 3명이 해당 안내서를 완성하였습니다.
댓글 한 개
This was really helpful to me. My Mini's screen suddenly popped off on one side. After running through this process I found that both screws on one hinge and one screw on the other had come out. It seems someone forgot to put Lock Tite on them! Within less than an hour the machine was back to its usual self. Thanks!