LG G3 Motherboard Replacement

소개

Use this guide to replace or remove the motherboard in the LG G3 (D855).

필요한 것

1 단계 Back Cover

LG G3 Motherboard Replacement, Back Cover: 1 단계, 이미지 1/2

LG G3 Motherboard Replacement, Back Cover: 1 단계, 이미지 2/2

Power off your phone before beginning disassembly.
Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover.
Pry the back cover up to separate its plastic clips.

번역하기

2 단계

Lift the back cover to release the rest of the plastic clips and remove it.
In case you can't lift the back cover completely, slide your fingernail or your prying tool around the midframe to release the remaining clips.
To reinstall the back cover, press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.

번역하기

3 단계 Battery

LG G3 Motherboard Replacement, Battery: 3 단계, 이미지 1/2

LG G3 Motherboard Replacement, Battery: 3 단계, 이미지 2/2

Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.

번역하기

4 단계

Lift the battery out of its recess and remove it.

번역하기

5 단계 Loudspeaker

LG G3 Motherboard Replacement, Loudspeaker: 5 단계, 이미지 1/1

Remove the four Phillips #00 screws (4 mm length).

번역하기

6 단계

Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover you used earlier to remove the back cover.
Pry up the plastic panel, including the loudspeaker, until you can get a good grip.

번역하기

7 단계

LG G3 Motherboard Replacement: 7 단계, 이미지 3/3

Carefully remove the plastic panel including the loudspeaker by gently pulling it away from the phone assembly.

번역하기

8 단계 Motherboard Cover Assembly

LG G3 Motherboard Replacement, Motherboard Cover Assembly: 8 단계, 이미지 1/1

Remove the eight Phillips #00 screws (4 mm length).

번역하기

9 단계

LG G3 Motherboard Replacement: 9 단계, 이미지 3/3

Insert an opening pick between the bottom right corner of the motherboard cover and the motherboard.
Pry up the motherboard cover to open the plastic clips which hold the cover in its place.
The clips can be a bit resistive. If you're having trouble prying up the motherboard cover, slightly rotate the opening pick sideways to make the process easier.
Work your way along the right edge.

번역하기

10 단계

LG G3 Motherboard Replacement: 10 단계, 이미지 3/3

Carefully lift the right edge of the motherboard cover.
The remaining plastic clips should open during this process or can be unhinged easily by hand.
Remove the motherboard assembly.

번역하기

11 단계 Motherboard

LG G3 Motherboard Replacement, Motherboard: 11 단계, 이미지 1/2

LG G3 Motherboard Replacement, Motherboard: 11 단계, 이미지 2/2

Use a spudger to pry up and disconnect the display flex cable.

번역하기

12 단계

Use a spudger to pry up and disconnect the digitizer flex cable.

번역하기

13 단계

Use a spudger to pry up and disconnect the rear camera flex cable.

번역하기

14 단계

Use a spudger to pry up and disconnect the front camera flex cable.

번역하기

15 단계

During these next few steps, make sure to avoid damaging the flex cables you disconnected.
Slide an opening pick under the bottom right corner of the motherboard and slowly pry it out of its recess by rotating the opening pick sideways.

번역하기

16 단계

Slide the opening pick under the right edge of the motherboard where the SIM card slot is located and pry it up by rotating the opening pick sideways.

번역하기

17 단계

Grab the top section of the motherboard and carefully lift it out of the phone.

번역하기

결론

If possible, turn on your device and test your repair before installing new adhesive and resealing.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers Community for help.