소개

The keyboard has 3 main parts, including the speaker cover, the heat sink, and the keyboard itself. You have to remove these in order to remove the keyboard.

부품

부품은 필요하지 않습니다.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

댓글 쓰기

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

댓글 쓰기

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

댓글 쓰기

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

댓글 쓰기

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

댓글 쓰기

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

댓글 쓰기

Locate the speaker cover.
  • Locate the speaker cover.

댓글 쓰기

Mac RAM 키트
Mac 속도를 높이십시오. 메모리를 최대한 활용하십시오.
Mac RAM 키트
Mac에서 메모리를 더 많이 확보하십시오.
Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - 답글

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

댓글 쓰기

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

댓글 쓰기

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

댓글 쓰기

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

댓글 쓰기

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - 답글

That isn't the HDD!

Dix Dox - 답글

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

댓글 쓰기

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

댓글 쓰기

Remove the heatsink.
  • Remove the heatsink.

댓글 쓰기

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

댓글 쓰기

Detach the ribbon cable.
  • Detach the ribbon cable.

댓글 쓰기

Remove the keyboard.
  • Remove the keyboard.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Sean Bent

회원 가입일: 2011년 04월 01일

41 평판

안내서 1개 작성함

Cal Poly, Team 10-39, Forte Spring 2011 Cal Poly, Team 10-39, Forte Spring 2011 회원

CPSU-FORTE-S11S10G39

5 회원들

안내서 6개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 1

지난 30일: 7

전체 시간: 1,819