물건을 수리하세요 커뮤니티 상점

Nerf Recon CS-6 Main Spring Replacement

소개

The main spring is responsible for creating the force required to launch the darts. Removing the spring allows access to other parts of the gun, or at this point, the spring itself can be replaced.

필요한 것

  1. Nerf Recon CS-6 Main Spring Replacement, Remove Magazine: 1 단계, 이미지 1개 중 1개

    • Skip this step if magazine is already removed.

    • Pull slide back.

    • Pull backwards on release buttons and slide magazine out.

    • Push slide back forward and pull trigger.

    편집

  2. Nerf Recon CS-6 Main Spring Replacement, Remove Visible Screws: 2 단계, 이미지 1개 중 1개

    • Use the Phillips #0 Screwdriver to remove these 9 screws.

    • All screws marked in red are 9.6 mm Phillips #0 screws.

    • Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

    편집

  3. Nerf Recon CS-6 Main Spring Replacement, Remove Hidden Screws: 3 단계, 이미지 2개 중 1개 Nerf Recon CS-6 Main Spring Replacement, Remove Hidden Screws: 3 단계, 이미지 2개 중 2개

    • Pull slide back to reveal more screws.

    • Remove these 2 screws.

    • Push slide forward.

    • Pull trigger to release compression of the main spring.

    • Screws are 9.6 mm Phillips #0.

    • Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

    편집

  5. Nerf Recon CS-6 Main Spring Replacement, Remove Plunger Cap: 4 단계, 이미지 1개 중 1개

    • Remove the screws on the plunger cap.

    • Tug the plunger cap off.

    • Screws are 9.6 mm Phillips #0.

    편집

  6. Nerf Recon CS-6 Main Spring Replacement, Remove Slide Screws: 5 단계, 이미지 1개 중 1개

    • Remove the 2 screws on the slide.

    • Screws are 9.6 mm Phillips #0.

    • Hold the two halves of the gun together to prevent any springs from launching out.

    편집

  7. Nerf Recon CS-6 Main Spring Replacement, Split the Gun in Half: 6 단계, 이미지 2개 중 1개 Nerf Recon CS-6 Main Spring Replacement, Split the Gun in Half: 6 단계, 이미지 2개 중 2개

    • Pull the gun apart at the middle seam.

    • Watch for any springs that might launch out.

    편집

  8. Nerf Recon CS-6 Main Spring Replacement, Remove Spring: 7 단계, 이미지 2개 중 1개 Nerf Recon CS-6 Main Spring Replacement, Remove Spring: 7 단계, 이미지 2개 중 2개

    • Pull the spring out the back of the gun.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 8명이 해당 안내서를 완성하였습니다.

작성자

3다른 기여자 명과 함께

Asad Qureshi

회원 가입일: 10/22/14

595 평판

안내서 3개를 작성함

배지: 18

배지 +15개 더

팀

Baylor, Team 8-14, Williams Fall 2014 Baylor, Team 8-14, Williams Fall 2014 회원

BU-WILLIAMS-F14S8G14

3 회원들

안내서 6개를 작성함

1가이드 댓글

Where can you buy replacement springs from?

Tom Hallam - 답글

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 8

지난 30일: 23

전체 시간: 6,286