Skip to main content

소개

A prerequisite guide for disconnecting the Li-ion battery in a Nintendo Switch.

  1. Remove the four 6.3mm Tri-point Y00 screws from the rear panel.
    • Remove the four 6.3mm Tri-point Y00 screws from the rear panel.

  2. Remove the single 6.1mm JIS #000 screw from underneath the kickstand.
    • Remove the single 6.1mm JIS #000 screw from underneath the kickstand.

  3. Remove the two 2.7mm JIS #000 screws from the bottom of the device.
    • Remove the two 2.7mm JIS #000 screws from the bottom of the device.

  4. Remove the single 2.7mm JIS #000 screw from the top of the device.
    • Remove the single 2.7mm JIS #000 screw from the top of the device.

  5. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  6. Remove the single 3.8mm JIS #0 screw from the right Joy-Con rail. Remove the single 3.8mm JIS #0 screw from the left Joy-Con rail.
    • Remove the single 3.8mm JIS #0 screw from the right Joy-Con rail.

    • Remove the single 3.8mm JIS #0 screw from the left Joy-Con rail.

  7. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device.
    • Pull the rear panel up and off of the device.

  8. Remove the single 3.1mm JIS #000 screw from micro SD card board.
    • Remove the single 3.1mm JIS #000 screw from micro SD card board.

  9. Lift the micro SD card board up and pull towards you to disconnect it from the motherboard. Lift the micro SD card board up and pull towards you to disconnect it from the motherboard.
    • Lift the micro SD card board up and pull towards you to disconnect it from the motherboard.

  10. Remove the six 3.1mm JIS #000 screws from the shield plate.
    • Remove the six 3.1mm JIS #000 screws from the shield plate.

  11. Remove the shield plate from the device. Remove the shield plate from the device.
    • Remove the shield plate from the device.

  12. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.
    • Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Blake Klein

회원 가입일: 2017년 01월 29일

42,860 평판

안내서 48개 작성하였습니다

You forgot to include removing the middle screws from both sides of the rails and also removing the screw from the SD card (As well as the SD card module itself) BEFORE removing the shield plate. I would also throw in a caution about removing the battery if you aren’t going to use the adhesive removal solvant as one could potentially damage the on board battery connector or the ribbon cable, depending on what they use to pry the battery out of the case. Other than that, great guide and it helped me to replace my battery w/o issues.

Kevin Chatterton II - 답글

You’re absolutely correct—thanks for catching that! I’ve updated the guides.

Blake Klein -

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 90