주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

소개

Follow this guide to replace the fan inside of your Nintendo Switch gaming console.

When reinstalling, make sure that you hook the right anchor point into the rubber grommet first before seating the fan.

  1. Remove the four 6.3 mm Tri-point Y00 screws from the rear panel.
    • Remove the four 6.3 mm Tri-point Y00 screws from the rear panel.

  2. Remove the single 6.1 mm Phillips #000 screw from underneath the kickstand.
    • Remove the single 6.1 mm Phillips #000 screw from underneath the kickstand.

  3. Remove the two 2.7 mm Phillips #000 screws from the bottom of the device.
    • Remove the two 2.7 mm Phillips #000 screws from the bottom of the device.

  4. Remove the single 2.7 mm Phillips #000 screw from the top of the device.
    • Remove the single 2.7 mm Phillips #000 screw from the top of the device.

  5. Remove the single 3.8 mm Phillips #000 screw from the right Joy-Con rail. Remove the single 3.8 mm Phillips #000 screw from the left Joy-Con rail.
    • Remove the single 3.8 mm Phillips #000 screw from the right Joy-Con rail.

    • Remove the single 3.8 mm Phillips #000 screw from the left Joy-Con rail.

  6. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device. Pull the rear panel up and off of the device.
    • Pull the rear panel up and off of the device.

  7. Remove the single 3.1 mm Phillips screw from micro SD card board.
    • Remove the single 3.1 mm Phillips screw from micro SD card board.

  8. Gently lift the micro SD card board straight up, away from the Switch to disconnect and remove it. During reassembly, line up the micro SD card board and lightly press on the foam pad until the press connector snaps into place to reconnect it.
    • Gently lift the micro SD card board straight up, away from the Switch to disconnect and remove it.

    • During reassembly, line up the micro SD card board and lightly press on the foam pad until the press connector snaps into place to reconnect it.

  9. Remove the six 3.1mm Phillips #000 screws from the shield plate.
    • Remove the six 3.1mm Phillips #000 screws from the shield plate.

  10. Remove the shield plate from the device. A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro. A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro.
    • Remove the shield plate from the device.

    • A thick pink thermal compound bridges the gap between the shield plate and the copper heat sink underneath. Use our thermal paste guide to remove the old thermal compound and replace it with an appropriate, thick compound such as K5 Pro.

  11. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard. Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.
    • Insert the pointed end of a spudger underneath the white connector and pry upwards to disconnect the battery from the motherboard.

  12. Remove the three 3.1mm Phillips #000 screws from the heatsink.
    • Remove the three 3.1mm Phillips #000 screws from the heatsink.

  13. Pull the heatsink up 45 degrees and rotate it to the right to remove. Pull the heatsink up 45 degrees and rotate it to the right to remove. Pull the heatsink up 45 degrees and rotate it to the right to remove.
    • Pull the heatsink up 45 degrees and rotate it to the right to remove.

  14. Remove the two 4.8mm JIS #000 screws from the fan.
    • Remove the two 4.8mm JIS #000 screws from the fan.

  15. Use a spudger to flip up the small gray locking flap on the fan ZIF connector. Use a spudger to flip up the small gray locking flap on the fan ZIF connector.
    • Use a spudger to flip up the small gray locking flap on the fan ZIF connector.

  16. Lift the left side of the fan out of its recess and rotate it 15 degrees towards you. Pull the fan out and away from you to unhook it from the rubber grommet. Pull the fan out and away from you to unhook it from the rubber grommet.
    • Lift the left side of the fan out of its recess and rotate it 15 degrees towards you.

    • Pull the fan out and away from you to unhook it from the rubber grommet.

결론

To reassemble your device, follow these instructions in reverse order.

다른 19명이 해당 안내서를 완성하였습니다.

Blake Klein

회원 가입일: 2017년 01월 29일

48,368 평판

안내서 48개 작성하였습니다

If your joycons are not charging, it could be the fans fault as they seem to share a 1.8v and or 5v rail, I had both joycons refusing to charge, and the fan was not working, so by replacing the fan, it had them charging properly again.

Corbin - 답글

There are a few steps left out, that really should be included.

First and most importantly, at Step 7 the MicroSD card slot needs to be removed before the shield plate can be removed. There is an additional screw to remove, and a cable to disconnect before the piece can be taken off. The shield plate won't come off until that has been done.

Secondly, it's easier to remove the fan and insert the new one if you fold back the board covering the grommet. To do so, remove two screws holding the black plastic piece in place (at the bottom-right of the fan. Then remove the single additional screw holding that board, disconnect the ribbon cable that covers the grommet, and fold the board gently to the side. That will expire the grommet and make it much easier to move the fan out and replace it.

Third, realistically before you can insert the new fan you need to remove a screw holding the rubber grommet in place and transfer the grommet to the new fan. None of this can be done until the step above had been done.

Adam Snell - 답글

You’re right about the Micro SD Card removal missing. I’ve gone ahead and added that step in. In regards to the the fan removal, removing the game card read/headphone jack board isn’t necessary for the fan removal.

Blake Klein -

thank you for the tip!

Tyler Wennstrom -

If I'm just replacing the fan, do I need to clean off/reapply any thermal paste?

Postponderance - 답글

댓글 쓰기

조회 통계:

24 시간 전: 50

7일 전: 406

30일 전: 2,388

전체 시간: 19,557