물건을 수리하세요 커뮤니티 상점

Nokia 2610 Circuit Board Replacement

필요한 것

  1. Nokia 2610 Circuit Board Replacement, Battery and Sim Card: 1 단계, 이미지 3개 중 1개 Nokia 2610 Circuit Board Replacement, Battery and Sim Card: 1 단계, 이미지 3개 중 2개 Nokia 2610 Circuit Board Replacement, Battery and Sim Card: 1 단계, 이미지 3개 중 3개

    • Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off.

    번역하기

  2. Nokia 2610 Circuit Board Replacement: 2 단계, 이미지 3개 중 1개 Nokia 2610 Circuit Board Replacement: 2 단계, 이미지 3개 중 2개 Nokia 2610 Circuit Board Replacement: 2 단계, 이미지 3개 중 3개

    • Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone.

    번역하기

  3. Nokia 2610 Circuit Board Replacement: 3 단계, 이미지 3개 중 1개 Nokia 2610 Circuit Board Replacement: 3 단계, 이미지 3개 중 2개 Nokia 2610 Circuit Board Replacement: 3 단계, 이미지 3개 중 3개

    • Lift the metal sim card holder (at the bottom of the battery slot) up and carefully pry the sim card out of its slot with a plastic opening tool or your finger.

    • After removal, lower the metal sim card holder into its original position.

    번역하기

  5. Nokia 2610 Circuit Board Replacement, Front Pannel: 4 단계, 이미지 2개 중 1개 Nokia 2610 Circuit Board Replacement, Front Pannel: 4 단계, 이미지 2개 중 2개

    • Insert the plastic opening tool into the crack between the front and back panels.

    • Gently pry the front cover away from the back cover while sliding the plastic opening tool towards the top of the phone.

    번역하기

  6. Nokia 2610 Circuit Board Replacement: 5 단계, 이미지 2개 중 1개 Nokia 2610 Circuit Board Replacement: 5 단계, 이미지 2개 중 2개

    • Lift the bottom of the front cover away from the phone.

    • Continue lifting until the top of the front cover is fully removed from the phone.

    • Note: To replace the Keypad, gently lift it out of the front cover. It is located below the clear viewing window.

    번역하기

  7. Nokia 2610 Circuit Board Replacement, Circuit Board: 6 단계, 이미지 1개 중 1개

    • Use the Torx screwdriver with the T6 attachmet to remove the 6 .4 mm screws around the outside of the circuit board.

    • Note: Removing the 4 T6 screws around the screen will loosen it, so don't worry if the screen also separates from the circuit board.

    번역하기

  8. Nokia 2610 Circuit Board Replacement: 7 단계, 이미지 3개 중 1개 Nokia 2610 Circuit Board Replacement: 7 단계, 이미지 3개 중 2개 Nokia 2610 Circuit Board Replacement: 7 단계, 이미지 3개 중 3개

    • Lift the circuit board out of the back cover.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 5명이 해당 안내서를 완성하였습니다.

작성자

5다른 기여자 명과 함께

Andrew Wood

회원 가입일: 10/05/10

336 평판

안내서 3개를 작성함

배지: 10

배지 +7개 더

팀

Cal Poly, Team 7-52, Amido Fall 2010 Cal Poly, Team 7-52, Amido Fall 2010 회원

CPSU-AMIDO-F10S7G52

4 회원들

안내서 12개를 작성함

1가이드 댓글

This is so cool tom!

Mo Chiggle - 답글

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 6

지난 30일: 15

전체 시간: 3,376