Skip to main content
  1. Slide the door located on the bottom of the camera in an outward direction
    • Slide the door located on the bottom of the camera in an outward direction

  2. Pull back on the red release tab located on the left side of the battery.
    • Pull back on the red release tab located on the left side of the battery.

  3. Slide battery out of camera
    • Slide battery out of camera

  4. Remove the 2 screws from the bottom of the camera
    • Remove the 2 screws from the bottom of the camera

  5. Using a Phillips head size 0 screwdriver, remove the screw from the right side of the camera
    • Using a Phillips head size 0 screwdriver, remove the screw from the right side of the camera

  6. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  7. Remove the 2 screws from the left side of the camera
    • Remove the 2 screws from the left side of the camera

  8. Separate the front casing from the back using a plastic opening tool, gently. Silver band and buttons will become loose when you remove the two pieces. Silver band and buttons will become loose when you remove the two pieces.
    • Separate the front casing from the back using a plastic opening tool, gently.

    • Silver band and buttons will become loose when you remove the two pieces.

  9. Pull the silver bracket off of the camera Pull the silver bracket off of the camera
    • Pull the silver bracket off of the camera

  10. Remove the 4 screws on the inner face of the camera. Circuit ribbon is attached at the top left of the camera. Be careful when separating the front and back of the camera. Pull the camera apart into 2 separate pieces.
    • Remove the 4 screws on the inner face of the camera.

    • Circuit ribbon is attached at the top left of the camera. Be careful when separating the front and back of the camera.

    • Pull the camera apart into 2 separate pieces.

  11. You should be left with 4 large pieces, the outer case, inner lens piece, outer silver band and back case containing the LCD display.
    • You should be left with 4 large pieces, the outer case, inner lens piece, outer silver band and back case containing the LCD display.

  12. Remove 4 screws holding the LCD screen in place. Be cautious of the brackets that come loose when you remove the 3 screws on the right side of the camera
    • Remove 4 screws holding the LCD screen in place.

    • Be cautious of the brackets that come loose when you remove the 3 screws on the right side of the camera

    • LCD Screen is attached to 2 ribbon wires

  13. Pull up on the small ribbon wire to disconnect it from the circuit board Flip the little black clip up to remove the larger ribbon wire from the circuit board.
    • Pull up on the small ribbon wire to disconnect it from the circuit board

    • Flip the little black clip up to remove the larger ribbon wire from the circuit board.

  14. Using a plastic separating tool, remove the LCD screen from the plastic casing.
    • Using a plastic separating tool, remove the LCD screen from the plastic casing.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Ryan Cosgrove

회원 가입일: 2012년 02월 10일

39 평판

안내서 1개 작성함

James Madison, Team 3-3, Klein Spring 2012 James Madison, Team 3-3, Klein Spring 2012 회원

JMU-KLEIN-S12S3G3

4 회원들

안내서 4개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 2

지난 30일: 4

전체 시간: 1,103