주요 콘텐츠로 건너뛰기

소개

This guide will provide instructions for removing and replacing the LED of the PlayStation VR Headset. This will require you to open the headset up, which may seem daunting at first, but can easily be done.

부품

지정된 부품이 없습니다.

  1. Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces. Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces. Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces.
    • Peel back the rubber covering around the lenses to remove the surrounding plastic eyepieces.

  2. Unscrew four 13 mm screws with a PH #000 screwdriver. Unscrew four 13 mm screws with a PH #000 screwdriver.
    • Unscrew four 13 mm screws with a PH #000 screwdriver.

  3. Using the plastic opening tool, carefully pry the white plastic panel free from the side of the headset. Repeat this action for the opposite side. Using the plastic opening tool, carefully pry the white plastic panel free from the side of the headset. Repeat this action for the opposite side.
    • Using the plastic opening tool, carefully pry the white plastic panel free from the side of the headset. Repeat this action for the opposite side.

  4. Use the plastic opening tool to pry the top white plastic panel free from the headset. Do not try to remove the bottom plastic panel. There is a screw attaching it that must be removed first. There may be a small amount of adhesive attaching the top panel to the headset, in which case you may need to use a bit more force to remove the panel.
    • Use the plastic opening tool to pry the top white plastic panel free from the headset.

    • Do not try to remove the bottom plastic panel. There is a screw attaching it that must be removed first.

    • There may be a small amount of adhesive attaching the top panel to the headset, in which case you may need to use a bit more force to remove the panel.

  5. 안드로이드 수리 키트

    새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

    지금 장보기

    안드로이드 수리 키트

    새 스크린 혹은 배터리는 단 하나의 키트로 충분합니다.

    지금 장보기
  6. Flip the headset over.
    • Flip the headset over.

    • Using a PH #000, unscrew the 7 mm screw found on the bottom of the headset.

  7. Using the plastic opening tool, pry the bottom white plastic panel loose and remove it from the headset. There is adhesive attaching the panel to the headset, in which case it will take more force to remove the panel. There is adhesive attaching the panel to the headset, in which case it will take more force to remove the panel.
    • Using the plastic opening tool, pry the bottom white plastic panel loose and remove it from the headset.

    • There is adhesive attaching the panel to the headset, in which case it will take more force to remove the panel.

  8. Unscrew the two 7 mm screws from the top of the headset. Unscrew the two 7 mm screws from the top of the headset. Unscrew the two 7 mm screws from the top of the headset.
    • Unscrew the two 7 mm screws from the top of the headset.

  9. Using your fingers, carefully pry the black front panel free from the headset. We recommend that you start the removal from the sides by pulling them forward. There is adhesive holding the front panel in place, which means you will need a bit of extra force to remove it.
    • Using your fingers, carefully pry the black front panel free from the headset.

    • We recommend that you start the removal from the sides by pulling them forward.

    • There is adhesive holding the front panel in place, which means you will need a bit of extra force to remove it.

  10. Unscrew the four silver 6 mm screws in each corner using a PH #000 screwdriver.
    • Unscrew the four silver 6 mm screws in each corner using a PH #000 screwdriver.

  11. Lift the small silver latch attaching the ZIF (zero insertion force) connector to the circuit board. Carefully pull the end of the white ribbon connector from its slot. Be careful not to damage or dirty the ribbon connector.
    • Lift the small silver latch attaching the ZIF (zero insertion force) connector to the circuit board.

    • Carefully pull the end of the white ribbon connector from its slot.

    • Be careful not to damage or dirty the ribbon connector.

  12. Unhitch the yellow led connector ribbon and move it aside. Be careful not to damage or dirty the ribbon connector.
    • Unhitch the yellow led connector ribbon and move it aside.

    • Be careful not to damage or dirty the ribbon connector.

  13. Carefully pry the black plastic piece attaching the yellow ribbon to the headset away from the green circuit board. Remove the yellow LED ribbons and black plastic connecting piece from the headset. Remove the yellow LED ribbons and black plastic connecting piece from the headset.
    • Carefully pry the black plastic piece attaching the yellow ribbon to the headset away from the green circuit board.

    • Remove the yellow LED ribbons and black plastic connecting piece from the headset.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Sarah Shand

회원 가입일: 2017년 02월 20일

1,094 평판

안내서 7개 작성하였습니다

USF Tampa, Team S3-G1, Sullivan Spring 2017 USF Tampa, Team S3-G1, Sullivan Spring 2017 회원

USFT-SULLIVAN-S17S3G1

3 회원들

안내서 7개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 12

30일 전: 33

전체 시간: 1,177