소개

This repair guide will give you step by step instructions on how to remove the Macintosh PowerBook 1400c Monitor.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

댓글 쓰기

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

댓글 쓰기

  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

댓글 쓰기

  • Locate the CD-ROM Drive latch.

댓글 쓰기

  • Slide the latch to the right to release the CD ROM drive.

댓글 쓰기

  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

댓글 쓰기

  • Locate the speaker cover.

댓글 쓰기

  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - 답글

  • Gently lift the speaker cover to remove it.

댓글 쓰기

  • Lift the keyboard up from the back using a spudger(wedge side).

댓글 쓰기

  • Gently lift the keyboard until only the ribbon cable remains attached.

댓글 쓰기

  • Tilt the keyboard away from the screen.

댓글 쓰기

  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - 답글

That isn't the HDD!

Dix Dox - 답글

  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

댓글 쓰기

  • Lift the heatsink from the side closest to the laptop screen.

댓글 쓰기

  • Remove the heatsink.

댓글 쓰기

  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

댓글 쓰기

  • Detach the ribbon cable.

댓글 쓰기

  • Remove the keyboard.

댓글 쓰기

  • Identify the right and left monitor end caps.

댓글 쓰기

  • Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.

댓글 쓰기

  • Once the end cap has been loosened by the spudger, pull outwards on the end caps.

댓글 쓰기

  • Completely remove both end caps.

댓글 쓰기

  • Identify the 4 total screw under the end caps (2 under each end cap).

    • The two outside 16mm long screws

    • The two inside 5.4mm long screws

댓글 쓰기

  • Lay the monitor all the way back.

댓글 쓰기

  • Remove the 4 screws using the Phillips #0 screwdriver.

댓글 쓰기

  • Identify the center cap of the monitor.

댓글 쓰기

  • Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.

댓글 쓰기

  • Detach the center cap completely.

댓글 쓰기

  • Identify the one 12.6mm long screw under the center cap.

댓글 쓰기

  • Remove the center screw with a Phillips #0 screwdriver.

댓글 쓰기

  • Lift upwards on the metal cover under the screw.

댓글 쓰기

  • Completely remove the metal cover.

댓글 쓰기

  • Identify where the left and right monitor cords are attached to the logic board

    • The base of the left monitor cord

    • The base of the right monitor cord

댓글 쓰기

  • To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.

댓글 쓰기

  • Completely detach the left monitor cord from the logic board.

댓글 쓰기

  • To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.

댓글 쓰기

  • Completely detach the right monitor cord from the logic board.

댓글 쓰기

  • Completely remove the monitor from the computer.

댓글 쓰기

결론

Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Taylor Chris

회원 가입일: 2011년 04월 01일

85 평판

안내서 1개 작성함

Cal Poly, Team 10-39, Forte Spring 2011 Cal Poly, Team 10-39, Forte Spring 2011 회원

CPSU-FORTE-S11S10G39

5 회원들

안내서 6개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 7

전체 시간: 2,507