기기를 수리하세요 커뮤니티 상점

TI-36X Pro Button Replacement

소개

For this guide you will remove all of the internal components in order to replace the buttons.

필요한 것

  1. TI-36X Pro Button Replacement, Back Cover: 1 단계, 이미지 1/2 TI-36X Pro Button Replacement, Back Cover: 1 단계, 이미지 2/2

    • Remove the calculator's protective cover.

    • Place the calculator face down.

    번역하기

  2. TI-36X Pro Button Replacement: 2 단계, 이미지 1/2 TI-36X Pro Button Replacement: 2 단계, 이미지 2/2

    • Using a Phillips #1 screwdriver, remove the six 6mm screws from the back of the case and place them to the side.

    • Start from the notches on the top edge and use your fingers or a prying tool to carefully pry the back cover from the calculator.

    번역하기

  3. TI-36X Pro Button Replacement, Battery: 3 단계, 이미지 1/2 TI-36X Pro Button Replacement, Battery: 3 단계, 이미지 2/2

    • Use a Phillips #00 screwdriver to remove the two 7.5 mm screws holding the battery cover to the case.

    • Remove the battery cover without disconnecting either end of the blue wire.

    • Use your finger to move the battery cover to the side.

    번역하기

  4. TI-36X Pro Button Replacement: 4 단계, 이미지 1/1

    • Use the flat side of a spudger to remove the battery by lifting the bottom edge.

    • When inserting a new battery, check the polarity (+ or -) and insert the new battery with the + side on top.

    번역하기

  6. TI-36X Pro Button Replacement, Button: 5 단계, 이미지 1/1

    • After removing the battery, use a Phillips #00 screwdriver to take out the 4.5mm screw directly to the right of the solar panel.

    • Do not disconnect any wires or you will need to solder them back on.

    번역하기

  7. TI-36X Pro Button Replacement: 6 단계, 이미지 1/1

    • Next, use a Phillips #00 screwdriver to remove the two screws located on each side of the striped ribbon between the two green circuit boards.

    번역하기

  8. TI-36X Pro Button Replacement: 7 단계, 이미지 1/1

    • Be careful not to scratch the gold lines on the circuit board since it may damage the circuit.

    • Carefully chisel off the 11 circular pieces that connect the lower circuit board to the calculator.

    • When reassembling the calculator, glue the lower circuit board back in place by dabbing glue into the holes that you chiseled.

    번역하기

  9. TI-36X Pro Button Replacement: 8 단계, 이미지 1/3 TI-36X Pro Button Replacement: 8 단계, 이미지 2/3 TI-36X Pro Button Replacement: 8 단계, 이미지 3/3

    • When removing the parts from the calculator be careful not to break any wires or ribbons. The solar panel, screen, and lower circuit board should remain connected throughout this guide.

    • Lift the top edge of the solar panel with a finger and slide it away from the circuit board to disconnect it from the calculator.

    • Carefully pry the screen out of the calculator with a prying tool or spudger.

    • Pry the lower circuit board from the calculator by inserting a prying tool between the base of the calculator and the circuit board.

    번역하기

  10. TI-36X Pro Button Replacement: 9 단계, 이미지 1/1

    • Grab one of the top corners of the gray rubber button pad and peel it off of the buttons.

    • If you turn the calculator over, all of the buttons will fall out.

    번역하기

  11. TI-36X Pro Button Replacement: 10 단계, 이미지 1/2 TI-36X Pro Button Replacement: 10 단계, 이미지 2/2

    • Locate the button that needs replacement and lift it out of the calculator with tweezers.

    • If the buttons do fall out, use the second picture to put them back properly.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Robert Sekerak

회원 가입일: 04/25/14

652 평판

안내서 4개 작성하였습니다

배지: 12

배지 +9개 더

팀

Cal Poly, Team 11-52, Amido Spring 2014 Cal Poly, Team 11-52, Amido Spring 2014 회원

CPSU-AMIDO-S14S11G52

4 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 18

전체 시간: 2,218