이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Power off your iPhone before beginning disassembly.
-
Remove the two 3.6 mm Pentalobe P2 screws next to the dock connector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the rear panel away from the back of the iPhone, being careful not to damage the plastic clips attached to the rear panel.
-
Remove the rear panel from the iPhone.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following four screws securing the cable cover to the logic board:
-
One 2.7 mm Phillips screw
-
One 2.6 mm Phillips screw
-
One 1.3 mm Phillips screw
-
One 1.2 mm Phillips screw
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the edge of a plastic opening tool to pry the cable cover tabs out of their slots cut into the EMI shield on the logic board.
-
Lift the cable cover from its edge nearest the top and remove it from the iPhone.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the edge of a plastic opening tool to pry the rear camera connector up from its socket on the logic board.
-
Remove the rear camera from the iPhone.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a SIM eject tool or a paperclip to eject the SIM and its tray.
-
Remove the SIM and its tray.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the five cables near the top of the logic board in the following order:
-
Headphone jack/volume button cable
-
Front facing camera cable
-
Digitizer cable
-
Display data cable
-
Power button cable (located underneath the headphone jack/volume button cable as shown in the second picture.)
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the 1.5 mm Phillips screw securing the grounding clip to the logic board near the headphone jack.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to pry the small grounding clip up off the logic board.
-
Carefully grasp the grounding clip and remove it from the iPhone.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Standoff Screwdriver for iPhones$5.49-
Remove the 4.8 mm standoff screw near the headphone jack.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the edge of a plastic opening tool to disconnect the Wi-Fi antenna from the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If present, peel the piece of black tape covering the hidden screw near the power button.
-
Remove the 2.6 mm Phillips screw securing the logic board near the power button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following screws securing the logic board to the case:
-
One 2.5 mm Phillips screw near the vibrator motor
-
One 2.4 mm Phillips screw
-
One 3.6 mm standoff along the side of the logic board nearest the battery opening.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully lift the logic board from the end closest to the speaker enclosure and slide it away from the top edge of the iPhone.
-
Remove the logic board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Wedge the plastic opening tool between the vibrator and the side of the iPhone.
-
Pry the vibrator up to release it from the adhesive securing it to the iPhone.
-
Remove the vibrator.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 2.4 mm Phillips screws from the sides of the speaker enclosure assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the small plastic bracket that was installed under the screw closest to the dock connector cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the small pieces of black tape covering the display mounting tabs.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the 1.5 mm Phillips screw securing the display assembly near the power button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Loosen the three large-headed Phillips screws along the volume button side of the iPhone about one half turn.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Loosen the three large-headed Phillips screws along the other side of the iPhone about one half turn.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the edge of a plastic opening tool to gently pry up the display assembly around its perimeter.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remember to switch the home button from your old display to the new display (in most cases, this is not provided). The home button gasket is thin rubber, so care must be taken not to tear it. Also, check that the mesh for the speaker hole is present in the replacement; if not, move it over from the old display.
-
Be sure to peel off the protective backing (usually blue or pink) from the new panel before installing it.
-
If your replacement display does not come with a 7 mm clear plastic ring surrounding the front-facing camera, be sure to transfer it between the old and new display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully straighten the digitizer and LCD data cables, and feed them through the slot cut in the outer case.
-
This photo shows the display assembly being installed incorrectly, with too much slack in the digitizer cable, which then forms a bend/loop that gets caught in the slot. The third photo also shows this loop.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
During reassembly, do not touch the metallic area at the base of the LCD data cable, as this can cause problems with the LCD. If you do touch it accidentally, clean it gently with an alcohol wipe before continuing.
-
After reassembly, protect your new display from any scratches by installing a new screen protector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the edge of a plastic opening tool to flip up the retaining flap on the home button ribbon cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a pair of tweezers to pull the home button cable out of its socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully de-route the home button cable through its slot in the outer case and remove it from the iPhone.
-
다른 45명이 해당 안내서를 완성하였습니다.