이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert a plastic opening tool into the seam between the front and back of the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert another plastic opening tool into the seam between the front and back of the iPod, leaving at least 1.5 inches of space between the two tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
At an angle, carefully insert a putty knife about 1/8 inch into the seam between the two opening tools.
-
Once the putty knife has cleared the lip of the rear panel, pivot the putty knife so that it is vertical, and carefully (but firmly) wiggle it straight down into the gap between the opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push with your fingers on the rear panel behind the putty knife to minimize bending. Slowly flex the putty knife, as shown in the picture, to ensure that most of the metal tabs on this side of the iPod are disengaged.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the putty knife from the iPod and reinsert it closer to the corner of the iPod, using the same wiggle method as before.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Between the lock slider and headphone jack, insert a plastic opening tool into the seam between the front and back of the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Near the center of the display, carefully insert a metal spudger into the gap created by the plastic opening tool.
-
Using the metal spudger, disengage the single clip on the top of the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Near the other top corner, insert an opening tool into the seam between the front and back of the iPod
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
On the other side, insert an opening tool into the seam between the front and back of the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the plastic opening tool from the top corner and insert it into the seam between the front and back of the iPod, leaving at least 1.5 inches of space between the two tools (as done on the other side).
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
At an angle, carefully insert a putty knife about 1/8 inch into the seam between the two opening tools.
-
Once the putty knife has cleared the lip of the rear panel, angle the putty knife so that it is vertical, and carefully (but firmly) wiggle it straight down into the iPod via the gap between the plastic opening tools.
-
Push with your fingers on the rear panel behind the putty knife to minimize bending. Ever so slightly flex the putty knife to ensure that most of the metal tabs on this side of the iPod are disengaged.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Carefully insert a metal spudger into the area near the stubborn metal clip.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Gently wiggle the metal spudger down so that it is all the way in the rear panel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to push up on the front panel with the metal spudger until the metal clip releases.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the front panel assembly with one hand and the rear panel with the other.
-
Gently (GENTLY) disengage the remaining clips on the rear panel by pulling the tops of the front and rear panels away from each other (think of the bottom of the iPod as a hinge), taking great care not to damage the ribbon cables holding the two halves together.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use angled tweezers or an opening tool to lift the brown lock latch straight up by 1 mm. Make sure you pull from both sides of the latch.
-
Grasp the flex cable with your fingers or tweezers and pull it straight up to disconnect it.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place the rear panel next to the iPod, being careful not to strain the orange headphone jack cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the hard drive up with one hand so you can access the headphone jack ribbon beneath.
-
Use a spudger to flip up the plastic tab holding the headphone jack ribbon in place. The tab will rotate up 90 degrees, releasing the ribbon cable.
-
Slide the orange headphone jack ribbon out of its connector.
-
The rear panel is now free from the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Now to repair the damage caused by liberating the internal parts of the iPod Classic! It is highly likely that at least one of the metal clips in the rear panel has been bent upward. These clips must all be pointing downward in order to reinstall the rear panel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Take the broad, flat side of the metal spudger and push the clip down, taking care not to tear the thin metal rail from the rear panel. Alternatively a pair of flat pin nosed pliers can be used to reduce risk of slipping and damaging the headphone jack.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
On a clean, hard surface, lay the rear panel on its side. Carefully but firmly push down on it, rolling the entire lip side back into its proper spot.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to lift the battery and the attached orange cable out of the iPod. If you have a 160 GB iPod, the battery will be thicker than the one pictured.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use one hand to hold the orange ribbon cables in place, and peel up the black tape securing the cables to the rear panel with your other hand.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two black Phillips screws securing the headphone jack to the rear panel.
-
These are SMALL! Be sure you have a size 00 screwdriver on hand
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following two screws:
-
One black Phillips screw securing the hold switch near the corner of the iPod.
-
One silver Phillips screw securing the other side of the hold switch.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the hold switch free from its housing on the rear panel. Don't remove the hold switch completely at this time, because it is connected to the same cable as the headphone jack.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the headphone jack out of its housing on the rear panel.
-
Lift the headphone jack and hold switch assembly out of the iPod.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If your replacement part does not include the plastic hold switch, follow the next steps to transfer the plastic hold switch to your new headphone jack.
-
Remove the single Phillips screw nearest to the hold switch.
-
Lift the plastic portion of the Hold switch away from the orange ribbon cable.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the small iPod opening tool to carefully peel the orange ribbon cable and attached black Hold switch up from the metal backing.
-
다른 226명이 해당 안내서를 완성하였습니다.
댓글 38개
This worked a charm for me! If you take it slow and steady, and keep all the warnings in mind, you shouldn't have too much trouble :)
check this guy I used dollar store xacto blades you got to be careful you can easily cut yourself but this method wont damage the clips or anything,