물건을 수리하세요 커뮤니티 상점

iRobot Roomba 891 Extractor Assembly Replacement

소개

This easy guide show you the steps to remove and replace the extractor assembly on your roomba.

필요한 것

  1. iRobot Roomba 891 Extractor Assembly Replacement, Battery: 1 단계, 이미지 2개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement, Battery: 1 단계, 이미지 2개 중 2개

    • Start by flipping your Roomba onto its back on a flat surface.

    • Be sure not to close the side brush bristles in the battery door during reassembly as shown by the handy warning in the second photo.

    번역하기

  2. iRobot Roomba 891 Extractor Assembly Replacement: 2 단계, 이미지 1개 중 1개

    • Unscrew both the 11mm Phillips #2 screws from the battery cover and remove cover from the Roomba.

    • These captive screws are not intended to be removed from the cover.

    번역하기

  3. iRobot Roomba 891 Extractor Assembly Replacement: 3 단계, 이미지 3개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement: 3 단계, 이미지 3개 중 2개 iRobot Roomba 891 Extractor Assembly Replacement: 3 단계, 이미지 3개 중 3개

    • Grasp the tabs on either side of the battery.

    • Remove the battery by pulling up on the tabs.

    • While you're here, check the battery contacts for corrosion or debris.

    번역하기

  4. iRobot Roomba 891 Extractor Assembly Replacement, Side Brush: 4 단계, 이미지 2개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement, Side Brush: 4 단계, 이미지 2개 중 2개

    • Remove the 7.5mm flat head #4 screw from center of the side brush.

    번역하기

  6. iRobot Roomba 891 Extractor Assembly Replacement: 5 단계, 이미지 1개 중 1개

    • Gently pull the side brush off of the motor hub.

    번역하기

  7. iRobot Roomba 891 Extractor Assembly Replacement, Extractor Assembly: 6 단계, 이미지 1개 중 1개

    • Remove the dustbin assembly from the Roomba.

    번역하기

  8. iRobot Roomba 891 Extractor Assembly Replacement: 7 단계, 이미지 3개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement: 7 단계, 이미지 3개 중 2개 iRobot Roomba 891 Extractor Assembly Replacement: 7 단계, 이미지 3개 중 3개

    • Unscrew the 2 phillips #2 11mm screws from roomba.

    • These captive screws will remain in the bottom cover after being loosened.

    번역하기

  9. iRobot Roomba 891 Extractor Assembly Replacement: 8 단계, 이미지 2개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement: 8 단계, 이미지 2개 중 2개

    • Lift the yellow tabs and lift the red cover from the extractor assembly.

    번역하기

  10. iRobot Roomba 891 Extractor Assembly Replacement: 9 단계, 이미지 1개 중 1개

    • Remove the rollers from the assembly by lifting it out from right side.

    번역하기

  11. iRobot Roomba 891 Extractor Assembly Replacement: 10 단계, 이미지 2개 중 1개 iRobot Roomba 891 Extractor Assembly Replacement: 10 단계, 이미지 2개 중 2개

    • Close the cover and remove the four 11mm Phillips #00 screws from the assembly.

    번역하기

  12. iRobot Roomba 891 Extractor Assembly Replacement: 11 단계, 이미지 1개 중 1개

    • Grasp the center of the assembly and remove from the roomba.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

2다른 기여자 명과 함께

Justin Tolin

회원 가입일: 05/29/19

736 평판

안내서 5개를 작성함

배지: 9

배지 +6개 더

팀

South Arkansas Community College, Team S1-G1, Mitchell Summer 2019 South Arkansas Community College, Team S1-G1, Mitchell Summer 2019 회원

SACC-MITCHELL-SU19S1G1

2 회원들

안내서 5개를 작성함

0가이드 댓글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 3

지난 30일: 17

전체 시간: 756