Hi @tator85704 Try turning off Voice Guide and see if that fixes it. Go to Settings > General Accessibility > Voice Guide Settings > Voice Guide

Hi @markfragola Here's the [문서: service manual] for the washer that may help. The fault codes posted by you seem to indicate a problem with multiple components e.g. drain pump (even though you've replaced it), pressure sensor, water inlet valves, lid lock etc. Maybe start on p.74 (p.75 of 83 pdf) of the manual and follow the checks for a fault code 18. If you find the problem and it is a faulty part that needs replacing, here's a parts list that is useful. Locate the wanted part in the list and note the part number for the part that is shown with it. Search online for the part number only, to find suppliers that suit you best.

Hi @techlord Since we don't know what you've tried, just verifying if you've done the following: (1) connected the PSU's 4 pin power cable to the 4 pin socket on the motherboard (see image below). If the PSU has an 8 pin cable you can break it in two and use just the one half. (2) connected a system speaker to the appropriate header pins on the Chassis Intrusion and speaker header pins (see image below) so that any beep codes can be heard. (3) installed the correct memory in the correct memory slot when using only one module (see image below) (4) performed a power refresh by disconnecting the power to the PSU, removing the cmos coin cell battery from the motherboard and then pressing and holding the power button operated for a full 30 seconds before releasing it. Reconnect the power to the PSU and check if the PC turns on. Doing this should reset the BIOS back to its default state in case it has become corrupted preventing a normal start. When the cmos battery is out, measure its voltage. If it is <2.5V DC...

Hi @jozedouglas The impurities in the water causes corrosion and provides circuit paths for the electricity which were not in the phone's operating design and could damage the components. The corrosion starts immediately and is ongoing until it is completely cleaned away First do not try to charge or to turn on your phone and then remove the battery as soon as possible from the phone to minimize any further damage. Then you need to dis-assemble the rest of the phone and clean all the affected parts using Isopropyl Alcohol 99%+ (available at electronics parts stores) to remove all traces of corrosion and water. If possible do not use "rubbing alcohol" as in some cases this is only 70% IPA or less, can contain additives which may leave conductive residues and is not as effective. If you do have to use it check the label to verify the amount of IPA. The higher the percentage of IPA the better Here is a link that describes what happens. Electronics Water Damage As always with electronics, especially surface...

Hi @iorekgivans Easiest option is to source a replacement 1.7mm (ID) x 4.0mm (OD) 20V/4A 90° DC barrel power plug connector and cut away the old plug where the cable is broken and re-terminate the cable on the new connector. Ensure that the +ve lead in the cable connects to the centre pin of the plug. I couldn't find a suitable 90° plug of the required size and voltage/current rating online the best I could find was this. If this suits you, search online for PP3-013 to find suppliers that suit you best.

Hi @dimphodee Have you tried using a different, known working compatible charger to see if the laptop stared charging and then worked OK? If the charger is OK it might be a faulty or loose USB-C charge port. Here's some answers to a previous question on ifixit about How to fix the usb c charging port for the model laptop that may help.

Hi @mickeyjarvis Have you checked if there's 19V DC on the output plug of the laptop charger? If the charger is OK it could be a faulty or loose DC in jack (link only to show image of part) If the DC In jack is faulty it will need to be replaced as it cannot be repaired. Here's a video that in general shows what needs to be done.

Hi @kathrynmat What is the model number of the washer? Have you tried pressing the Start/Pause button to stop the washer during a cycle so that the lid unlocks?

Hi @wrrhhcykbdmdy7u What is the model number of the camera? Take some pictures and then download them to a computer and check what they look like. If they are OK then it could be a faulty LCD screen. If they are no good, it could be a faulty motherboard or image sensor in the camera.

Hi @sebastianw94509 Here's an article that shows how to install Bazzite in a laptop. In the article the minimum system requirements state that the GPU must support Vulkan 1.3+. Here's an article that shows how to find out if your laptop supports it or not.