이 사용자는 아직 프로필을 작성하지 않았습니다.
질문
How do I solder two layers back together when the top layer is slightly bent at the top? Thanks in advance!
더 읽어보기Hey there peeps, Pretty new with MacBook repairs. So got a MacBook Pro A1707 (820-00281-A) which is dead. Checked...
더 읽어보기Got an 8 with a too sensitive home button, replace turtle but still its the same… any ideas why?
더 읽어보기Hello guys, Had an iPhone 8 come in with NO boot, Fixed a short on VDD_MAIN. One cap was shorted near PMIC. Now the Phone...
더 읽어보기Hello People, Customer Brought in an iPhone XS with NO IMEI, Took apart the board and there is a short on...
더 읽어보기iPhone 7 Came in with NO BOOT, there was previous work done and the previous tech had changed the NAND. Popped it under a...
더 읽어보기Hey, Got an iPhone 7+ with NO BACK and FRONT CAMERA. Measured PP1V2_NV_VDD_CONN & PP1V2_UT_VDD_CONN. Found out that there...
더 읽어보기Hey, Very weird problem I have encountered here. Checked Panic Logs and it says something regarding to i2c3. Attached the...
더 읽어보기have an iPhone 6s which came in with no power, upon plugging it in it bootloops. Remove the cable and it dies. Under...
더 읽어보기Was doing an SSD upgrade and now its not even detecting the previous apple ssd, Please help Im pretty new in terms of MAC...
더 읽어보기4 페이지 중 1
답변
Those lines arent shot, theyre low resistance lines so most multimeters will beep or indicate a short. You can send in your phone for repairs if youre not so experienced and dont have the tools. You are from?
더 읽어보기Does it take proper charging voltage? If yes it's most probably a faulty NAND or NAND Power line. But as your customer said it was plugged in immediately points to Tristar so i would first take a look at the charging circuit. Do let me know what do you find, It would be easier if you had an ICC pro. It would’ve told you if its a tristar fault without opening the iPad.
더 읽어보기Sounds like a bad battery, Just replace your battery and check. If that doesn’t fix it bring it in to a reputed micro-soldering company for them to take a look at it. Cheers!
더 읽어보기Try replacing the above part and see if it works, I dont recall properly as to what is that antenna. If i do recall i’ll be suree to update it here. I think its a nfc antenna but I may be wrong.
더 읽어보기Sounds like a bad charging port. Replace it with an OEM charging port pulled from an iCloud locked device. Should fix the issue!
더 읽어보기Rice wont do any good to your water damaged phone. You can try your DFU restores but I suspect that its the Display itself or the Board because you said it has a cracked back water might have seeped in through the back damaging touch function. I suggest you take it in a reputed repair store and let the take a look. I’m sure it’s not that a big issue if they have the right tools to figure it out!
더 읽어보기What happens when you try to restore it? Error 4013?
더 읽어보기Well with a bit of common sense, you will realize its not the Charging IC itself that has gone bad. It is some other small component on the charging IC line that is causing it to heat up. If you have a thermal camera its the best time to put it to use and find that bad cap.
더 읽어보기You’ll need to open the device to remove the camera as when you remove the glass it may damage the lens itself and it will cost you a bomb. So its better to open the phone entirely and change the lens. Hope that helps :)
더 읽어보기Seems like you knocked off some important baseband related caps, you need to install them and also you knocked off the homer ic which controls vibration. You need to reball that and fix that too. Hope this helps :D
더 읽어보기4 페이지 중 1
Myron.
@iammyron07
127
평판
34
해결책
0
안내서
회원 가입일 11/06/19
투표
5
0