Student-Contributed Wiki

학생-기여 위키

해당 위키는 저희 교육 프로그램의 멋진 학생이 작성하였습니다. iFixit 직원이 관리하지 않습니다.

Vivitar ViviCam T027 Troubleshooting

Flash Does Not Go Off ¶ 

Flash does not work when flash button is pressed.

Camera is in Macro Mode ¶ 

If the camera is in macro mode, the flash will automatically be disabled. Take the camera out of macro mode or reset it to turn on the flash.

Battery is Low ¶ 

The flash will not work if the battery is low. Try recharging or replacing your battery.

Flash May Need to be Replaced ¶ 

If the flash still does not work, it may need to be replaced.

SD Card Stuck in Camera ¶ 

The SD card is difficult to remove or will not remove from the device.

SD card Incorrectly Inserted ¶ 

If your SD card is stuck in the device, it may have been inserted incorrectly. Try carefully removing the card with tweezers.

Lens Will Not Extend ¶ 

The Lens will not extend when taking a photo resulting in blurry and unclear photos.

Refresh the Camera to Extend Lens ¶ 

If the lens is stuck and not extending out, try to refresh your camera. This can be done by removing the SD card and battery. Wait for a bit then reinstall the SD card and battery and power on the device.

Dust and Obstructions Preventing Lens from Extending ¶ 

Look for dust and other obstructions that may be preventing the lens from extending. To clean this out use a q-tip.

Lens Jammed ¶ 

Gently tap the metalwork just in case it got stuck by pressure while in its case. If this does not work, you may have to replace the lens. See how to replace the lens in this guide.

Power Button Does Not Work ¶ 

Power button does not turn camera on when pressed down.

Camera won’t turn on ¶ 

If the camera does not turn back on after being shut off, you may have to take out the batteries and reinsert them to power the camera back up again.

“Auto Power Off” ¶ 

If the camera shuts off automatically, you may have selected the “Auto Power Off” option in order to conserve battery power. To turn this option off, go through the “Set” options until you reach the screen to disable “Auto Power Off”.

Check batteries ¶ 

If the camera does not turn on, the batteries may be dead. Replace with new AAA batteries and try again.

On button is jammed ¶ 

If the on button is jammed or broken, you will not be able to turn on the camera. You may need to replace the on button.

The Screen is Broken ¶ 

You may get a black screen after trying to turn on the camera, which probably means the LCD screen is damaged. Learn how to replace the screen in this guide.

Batteries: Trouble Replacing and Charging ¶ 

Batteries are not working and will not turn the camera on.

Wrong Type of Batteries ¶ 

If you place new batteries in the camera but it does not power on, it may be because you are using the wrong kind of batteries. Ni-CD batteries may not be suitable for this device as they have a low voltage. Try using Ni-MH or alkaline batteries instead.

댓글 한 개

Thank you, thank you, THANK you!

My Vivitar 8018 camera just didn't want to flash and I thought it was either defective from the factory or perhaps broken in packaging, hard use, etc.

It never occurred to me that the flash is not made to be used in the macro mode, which is the topmost comment in your troubleshooting guide.

Strange thing is; my camera's flash doesn't want to go off in the MICRO mode, only in the MACRO mode! Either way, I got the damned flash to go off, so I'm able to use it now.

stevemarcusaz - 답글

조회 통계:

지난 24시간: 2

지난 7일: 22

지난 30일: 80

전체 시간: 4,705