Skip to main content

Third generation of iPad with Wi-Fi, released on March 16, 2012. Model Number A1416. Repair requires heating and careful prying.

182 질문 전체 보기

Digitizer does not work

Hi have changed the back light IC on the logic board. The back light issue is solved after replacing the back light IC but like always it is some or the other with ipads .

After hooking up everything the touch doesn't work, I have used 5 different digitizer to see if it is digitizer issue but neither one works and I dont know what could have happened .

Please suggest.

답변되었습니다! View the answer 저도 같은 문제를 겪고 있습니다

좋은 질문 입니까?

점수 2

댓글:

[image|806990] I hope this will work

의 답변

의견 추가하세요

아이폰 배터리 수리 키트

Only $29.99

Buy Now

아이폰 배터리 수리 키트

Only $29.99

Buy Now

4개의 답변

선택된 해법

I suggest you knocked something off the board or used too much heat or damaged the connector. Look for missing components, balls of solder which do not belong, and/or any type of visible damage.

Next look at the schematics and troubleshoot touch circuit.

EDIT:

@touchwireless in the red circle most to the right in your picture, there seems to be a small component, possibly a resistor bridging two capacitors C3106 and C3108. Those 2 caps are on an important line shooting out from a touch IC. Remove that component and see if that solves it. Unless it is an artifact from the picture...

Here, that small guy in the middle of this circle, the only vertically positioned component:

Block Image

Block Image

해당 답변은 도움이 되었습니까?

점수 2

댓글:

I am not good at soldering this is something I am trying to do and this is freeking me out

의 답변

what if i have used too much heat will the ipad still turn on ?

의 답변

It should, so that you be careful. If you apply unnecessary amounts of heat to remove the shields, you kill the phone. Practice with scrap iPhone 6 boards first. They are a special breed when it comes to shield removal.

의 답변

how should i know if thats the overheat issue

의 답변

is it fixable? if not I ruined the customers ipad

의 답변

7에 댓글 더 나타내기

의견 추가하세요

Block Image

here is the pic for the logic board I worked on

해당 답변은 도움이 되었습니까?

점수 0

댓글:

I'll look at my schematics and get back to you. It does seem like you bridged something unless this is due to the bad image quality.

Can you add a high-resolution close-up picture of the area circled in red?

의 답변

의견 추가하세요

Block Image

Heading text

해당 답변은 도움이 되었습니까?

점수 0

댓글:

I hope this will work for you Rany

의 답변

Yes something is not right. You seem to have a component shorting two caps. They are on the same line, but it could be shorting them to ground and causing this. You need to remove it.

의 답변

의견 추가하세요

Block Image

here is the picture marked with "A" and "B" could you please tell me which one to remove?

해당 답변은 도움이 되었습니까?

점수 0

댓글:

@touchwireless check the picture I added last.

의 답변

Thank you I will update one I do this

의 답변

의견 추가하세요

귀하의 답변을 추가하십시오

Touch Wireless 가/이 대단히 고마워 할 것입니다.
조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 2

전체 시간: 297