물건을 수리하세요 커뮤니티 상점
수리 커뮤니티 가입 - 계정 만들기

Repair guides and support for your Samsung TV.

20 질문 전체 보기 | 6 부품 둘러보기

옵션

Standby light not on

Hi I have a MU6100 so slightly different. My exact model is UA43MU6100S. Issue is standby light is not on. If I unplug the cable between the PSU and mainboard the backlights turn on.There is a test point to measure 8v stby and 13v on this point is always at 13v it will drop to about 8.5 volts for very briefly when connecting back cable to main board when unplugging and measuring voltages pin A/D is 3.2v unplugged and 0.08 connected 0d_US is 3.6 unplugged and 3.3 connectedBLU_PWM is 3.2 unplugged and 0.04 connected power on/off is 4.6 unplugged and 3.3 connected. I have tried disconnecting the 2 LCD flat panel cables to eliminate a panel fault.If I hold the power button on remote a few seconds the standby red lights up for another few seconds then give 1 flash and goes off.

Update (09/02/23)

Block Image
Block Image
Block Image
이 질문에 답하기 저도 같은 문제가 있습니다

좋은 질문입니까?

예 아니요
점수 1
댓글 1개

[image|3061367][image|3061368]

의

댓글 달기

답변 2개

필터 기준:
가장 유용함 가장 최근 가장 오래된
가장 유용한 답변

옵션

Hi @shaun63172,

Try disconnecting the TV power button board cable from the mainboard and see if the TV turns on using the remote.

This won't work if the IR receiver is on the same board as the power button.

Just wondering if the button is "stuck" in the operated position so the TV doesn't know whether to turn on or off.

If no good, try removing the batteries from the remote and use the TV controls and check

이 답변이 도움이 되었나요?

예 아니요
점수 1
댓글 달기

옵션

@shaun63172 we need to see your boards to follow your power measurements. Since your back lights come on it is a pretty good indication that your Power supply is okay. This sounds pretty much like a failed main board.

기존 질문에 이미지 추가하기

이 답변이 도움이 되었나요?

예 아니요
점수 0

댓글 10개:

Hi @shaun63172,

Try disconnecting the TV power button board cable from the mainboard and see if the TV turns on using the remote.

This won't work if the IR receiver is on the same board as the power button.

Just wondering if the button is "stuck" in the operated position so the TV doesn't know whether to turn on or off.

If no good, try removing the batteries from the remote and use the TV controls and check

의

Yes have tried disconnecting both boards as well as the WiFi / bluetooth board but still same issue.

의

[image|3061367][image|3061368]

의

@shaun63172 see if you can get some pictured that are zoomed in.It's difficult to enlarge the ones you have attached since they get fuzzy on close up. Typical Samsung. Put more goop on the Mosfets.....what a mess on the board :-)

We need to see the connector CNM803 where the main board connects to.

의

Have added a close up of CNM803

의

댓글 5개 더보기

댓글 달기

답변을 추가하세요

Shaun 영원히 감사할 것입니다.
조회 통계:

지난 24시간: 0

지난 7일: 1

지난 30일: 7

전체 시간: 153