주요 콘텐츠로 건너뛰기

Merch Source Projector Entertainment II Motherboard

필요한 것

  1. Merch Source Projector Entertainment II Motherboard, Outer Casing: 1 단계, 이미지 1/2 Merch Source Projector Entertainment II Motherboard, Outer Casing: 1 단계, 이미지 2/2
    • Flip the projector onto its back and unscrew the nine 15mm screws using the Phillips #0 screw driver.

  2. Merch Source Projector Entertainment II Motherboard: 2 단계, 이미지 1/1
    • Flip the projector right side up and unscrew the two 12mm screws on the light bulb panel located at the rear of the projector with a Phillips #0 screw head.

    • The bottom right panel screw does not come completely out the panel door.

  3. Merch Source Projector Entertainment II Motherboard: 3 단계, 이미지 1/2 Merch Source Projector Entertainment II Motherboard: 3 단계, 이미지 2/2
    • Using your hands, gently pry the top and bottom of the projector casing apart.

  4. Merch Source Projector Entertainment II Motherboard, Motherboard: 4 단계, 이미지 1/2 Merch Source Projector Entertainment II Motherboard, Motherboard: 4 단계, 이미지 2/2
    • Use the plastic opening tool to gently disengage the ribbon cable from its back housing.

    • Once the ribbon cable is disengaged gently pull the cable off the motherboard.

    • Once the housing is disengaged, the ribbon cable should slide out easy. Do not pull too hard on the ribbon cable as it is very fragile.

  5. Merch Source Projector Entertainment II Motherboard: 5 단계, 이미지 1/2 Merch Source Projector Entertainment II Motherboard: 5 단계, 이미지 2/2
    • Unscrew the three 6 mm screws from the motherboard with the Phillips #0 screwdriver.

    • Be sure not to damage any of the wires atached to the motherboard.

  6. Merch Source Projector Entertainment II Motherboard: 6 단계, 이미지 1/2 Merch Source Projector Entertainment II Motherboard: 6 단계, 이미지 2/2
    • Solder off all of the connections on the motherboard with a soldering iron.

    • Once connections are soldered off, the motherboard should be detached and ready for replacement.

    • Need some help? Follow this guide to learn soldering basics.

    • While soldering the metal connections can get very hot. Never touch the iron with your hand. also make sure that the projector is fully turned off and not plugged in.

    • If there is hot glue on top on the connection with the motherboard, you will need to peel it off using your fingers.

결론

To reassemble your device, follow these instructions in reverse order.

Michael Tan

회원 가입일: 01/08/15

587 평판

안내서 3개 작성하였습니다

Cal Poly, Team 30-3, Green Spring 2015 Cal Poly, Team 30-3, Green Spring 2015 회원

CPSU-GREEN-S15S30G3

4 회원들

안내서 10개 작성하였습니다

댓글 3개

Was wondering if you could help me identify a microchip on the board by the speaker?

Brad Langland - 답글

Where can I get parts for the projector? I think my board is cooked.

Delgtm - 답글

mine acts like it does not recognize the rca cords. help

Kamela Mitchell - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 4

전체 시간: 1,810