기기를 수리하세요 커뮤니티 상점

OLPC XO-4 Touch Screen Frame Replacement

소개

Use this guide to remove the frame from the screen on your OLPC XO 4.0 Touch.

필요한 것

  1. OLPC XO-4 Touch Screen Frame Replacement, Battery: 1 단계, 이미지 1/1

    • Turn the laptop upside-down, with the handle facing away from you.

    편집

  2. OLPC XO-4 Touch Screen Frame Replacement: 2 단계, 이미지 1/2 OLPC XO-4 Touch Screen Frame Replacement: 2 단계, 이미지 2/2

    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    편집

  3. OLPC XO-4 Touch Screen Frame Replacement: 3 단계, 이미지 1/2 OLPC XO-4 Touch Screen Frame Replacement: 3 단계, 이미지 2/2

    • Lift up on the middle of the battery to remove it from the device.

    편집

  5. OLPC XO-4 Touch Screen Frame Replacement, Screen Frame: 4 단계, 이미지 1/3 OLPC XO-4 Touch Screen Frame Replacement, Screen Frame: 4 단계, 이미지 2/3 OLPC XO-4 Touch Screen Frame Replacement, Screen Frame: 4 단계, 이미지 3/3

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    편집

  6. OLPC XO-4 Touch Screen Frame Replacement: 5 단계, 이미지 1/3 OLPC XO-4 Touch Screen Frame Replacement: 5 단계, 이미지 2/3 OLPC XO-4 Touch Screen Frame Replacement: 5 단계, 이미지 3/3

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

    편집

  7. OLPC XO-4 Touch Screen Frame Replacement: 6 단계, 이미지 1/1

    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

    편집

  8. OLPC XO-4 Touch Screen Frame Replacement: 7 단계, 이미지 1/2 OLPC XO-4 Touch Screen Frame Replacement: 7 단계, 이미지 2/2

    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 6명과 함께

Ji Kim

회원 가입일: 01/25/13

18 평판

안내서 3개 작성하였습니다

배지: 8

배지 +5개 더

팀

Cal Poly, Team 3-29, Amido Winter 2013 Cal Poly, Team 3-29, Amido Winter 2013 회원

CPSU-AMIDO-W13S3G29

4 회원들

안내서 20개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 1

30일 전: 1

전체 시간: 211