이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Handling it by the tabs on either end, place a heated iOpener over the top edge of the iPad.
-
Let the iOpener sit on the iPad for two minutes to soften the adhesive securing the front panel to the rest of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
As you follow the directions, take special care to avoid prying in the following areas:
-
Home Button
-
Front Facing Camera
-
Main Camera
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Anti-Clamp$24.95-
Elevate the iPad enough for the Anti-Clamp's arms to rest above and below the screen.
-
Pull the blue handle towards the hinge to disengage opening mode.
-
Position the suction cups near the top edge of the iPad—one on the front, and one on the back.
-
Push down on the cups to apply suction to the desired area.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push the blue handle away from the hinge to engage opening mode.
-
Turn the handle clockwise until you see the cups start to stretch.
-
Wait one minute to give the adhesive a chance to release and present an opening gap.
-
Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next two steps.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Place a suction cup over the iPad's front-facing camera and press down to create a seal.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Firmly pull up on the suction cup to create a small gap between the front panel and the rear case.
-
Once you've opened a sufficient gap, insert an opening pick into the gap to prevent the adhesive from resealing.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the pick along the edge of the display, towards the headphone jack.
-
If there is still a considerable amount of resistance when sliding the opening pick, repeat the iOpener heating procedure and apply additional heat.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Bring the right opening pick down and around the top right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Reheat the iOpener and lay it over the right edge of the display to loosen the adhesive underneath.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick about halfway down the edge of the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the opposite opening pick down to the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick down the edge of the display until you reach the corner.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Bring the right-hand opening pick around the bottom corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the left-hand opening pick along the bottom edge of the display, then remove it from the bottom right corner of the iPad.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use picks to ensure most of the adhesive has been cut through on the top, left, and bottom sides.
-
Twist the top and bottom picks to separate the display assembly from the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Swing the display assembly towards the right of the case, using the right edge as a hinge.
-
As you move the display assembly, make sure that the display ribbon cable is not being stressed.
-
Continue swinging the display assembly until it lays flat next to the rear case.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a Phillips screwdriver to remove the eleven 1.3 mm screws securing the EMI shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Apply a heated iOpener to the EMI shield on the logic board for one minute.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the logic board EMI shield, starting at the edge nearest the top of the iPad.
-
Slowly peel the EMI shield up from the logic board.
-
Remove the logic board EMI shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a Phillips driver to remove the 1.7 mm-long screw securing the battery connector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Squeeze the sharp protrusion with a pair of pliers to flatten it.
-
Repeat the process for all sharp protrusions along the edges of the EMI shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide the battery blocker underneath the left side of the logic board's battery connector at a 35 degree angle.
-
Leave the battery blocker in place as you work.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Apply a few drops of high-concentration (90% or higher) isopropyl alcohol under the logic board to the left and right of the battery connection.
-
Wait one minute for the isopropyl alcohol to weaken the adhesive under the logic board.
-
Try to insert the battery blocker. If the logic board doesn't easily lift up, apply a few more drops of isopropyl alcohol.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a Phillips screwdriver to remove the three 1.3 mm Phillips screws securing the display cable bracket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of the spudger to disconnect the display assembly connector from the motherboard socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Slide an opening pick under the right ambient light sensor to loosen its adhesive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a Phillips screwdriver to remove the four 1.9 mm-long screws securing the upper speaker to the frame.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Apply a few drops of high-concentration (90% or higher) isopropyl alcohol under the upper speaker.
-
Wait one minute for the isopropyl alcohol to weaken the adhesive under the upper speaker.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to push the left side of the upper speaker toward the battery just enough for the left speaker to slide out of its recess in the frame.
-
다른 2명이 해당 안내서를 완성하였습니다.