주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

소개

Use this guide to replace a weak battery in your Huawei Mate 10 Pro.

Before disassembling your phone, discharge the battery below 25%. The battery can catch fire and/or explode if accidentally punctured, but the chances of that happening are much lower if discharged.

  1. Switch off your phone.
    • Switch off your phone.

    • Prepare an iOpener and apply it to the back of the phone for about two minutes to loosen the adhesive beneath the back cover.

  2. Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger. Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone. Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.
    • Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger.

    • Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone.

    • Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.

  3. Don't remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard. Flip the back cover over to the side.
    • Don't remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard.

    • Flip the back cover over to the side.

    • Remove the Phillips #00 screw which holds down the metal shield, sitting on top of the connection of the fingerprint sensor cable.

  4. Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

    Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기
  5. Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor. Disconnect the fingerprint sensor cable with a spudger.
    • Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor.

    • Disconnect the fingerprint sensor cable with a spudger.

    • When reassembling your phone apply new adhesive where it is necessary.

  6. Remove the twelve Phillips #00 screws. Carefully remove the shields on top of the motherboard and the charging board. In case the shields do not pop out easily on their own after you removed the Phillips screws, you can use the pointed end of a spudger to pry them out.
    • Remove the twelve Phillips #00 screws.

    • Carefully remove the shields on top of the motherboard and the charging board.

    • In case the shields do not pop out easily on their own after you removed the Phillips screws, you can use the pointed end of a spudger to pry them out.

  7. Use a spudger to disconnect the charging port flex cable from the motherboard and from the daughterboard. Use a spudger to disconnect the charging port flex cable from the motherboard and from the daughterboard.
    • Use a spudger to disconnect the charging port flex cable from the motherboard and from the daughterboard.

  8. Use a pair of tweezers to carefully remove the charging port including its flex cable. The charging port sits tightly in its recess. In case you have trouble removing it, use the flat end of a halberd spudger to pry it out.
    • Use a pair of tweezers to carefully remove the charging port including its flex cable.

    • The charging port sits tightly in its recess. In case you have trouble removing it, use the flat end of a halberd spudger to pry it out.

  9. Use a spudger to disconnect the battery flex cable. Apply an iOpener on the screen for at least one minute to loosen the adhesive beneath the battery.
    • Use a spudger to disconnect the battery flex cable.

    • Apply an iOpener on the screen for at least one minute to loosen the adhesive beneath the battery.

  10. The display flex cable runs underneath the battery. So be careful not do damage it when loosening the adhesive. Also take care not to bend or puncture the battery at any time. Use a spudger to carefully pry up the battery and slide along the side to separate the adhesive. Remove the battery.
    • The display flex cable runs underneath the battery. So be careful not do damage it when loosening the adhesive. Also take care not to bend or puncture the battery at any time.

    • Use a spudger to carefully pry up the battery and slide along the side to separate the adhesive.

    • Remove the battery.

    • When reassembling your phone replace the old adhesive with double-sided tape or pre-cut adhesive.

결론

To reassemble your device, follow these instructions in reverse order.

다른 5명이 해당 안내서를 완성하였습니다.

Dominik Schnabelrauch

회원 가입일: 2016년 11월 23일

64,638 평판

안내서 292개 작성하였습니다

iFixit iFixit 회원

Community

126 회원들

안내서 11,884개 작성하였습니다

complimento ottima guida

coroby - 답글

The battery was glued in really firmly. I ended up pulling it out with a plier and had some smoke and sparks, luckily I had made sure to drain it completely prior to repair.

Martin Olsson - 답글

Hi there, I completed the battery replacement nicely with all your steps, the phone could turn on and function normally, the only issue after the battery replacement is the phone has no sound and vibration. I have ensure all connectors are back to place securely. Does anyone have any clue of the cause of no sound and no vibration?

Shawn W - 답글

댓글 쓰기

조회 통계:

24 시간 전: 24

7일 전: 191

30일 전: 855

전체 시간: 10,553