주요 콘텐츠로 건너뛰기

소개

Replacing the motherboard will require time and patience, as multiple steps are in this guide. Ensure the laptop is powered off, and be cautious when working around the motherboard, as its cables and plugs are fragile.

  1. Flip the laptop over with the screen facing down to reveal the bottom panel. Unscrew each of the highlighted screws with a Phillips #0 screwdriver. Unscrew each of the highlighted screws with a Phillips #0 screwdriver.
    • Flip the laptop over with the screen facing down to reveal the bottom panel.

    • Unscrew each of the highlighted screws with a Phillips #0 screwdriver.

  2. Use a metal spudger to remove fitting and reveal the screw. Use a screwdriver with a Torx T7 bit to remove the screw. Use a screwdriver with a Torx T7 bit to remove the screw.
    • Use a metal spudger to remove fitting and reveal the screw.

    • Use a screwdriver with a Torx T7 bit to remove the screw.

  3. The SD Card slot  is on the top right corner of the device near the headphone jacks. Depress the fake SD Card and release. Pull the fake SD Card out and remove it completely from the slot, as this will help in the removal of the backplate.
    • The SD Card slot is on the top right corner of the device near the headphone jacks.

    • Depress the fake SD Card and release.

    • Pull the fake SD Card out and remove it completely from the slot, as this will help in the removal of the backplate.

  4. Lift the back plate starting at the opposing edge to the SD card. Lift from left to right and continue lifting this plate at this angle until it's free from the laptop. Once the backplate is completely off, this will reveal the inside components of the device.
    • Lift the back plate starting at the opposing edge to the SD card. Lift from left to right and continue lifting this plate at this angle until it's free from the laptop.

    • Once the backplate is completely off, this will reveal the inside components of the device.

    • Upon reassembly of the back cover, make sure to line up the two headphone jacks on the upper right corner with the holes in the back cover or else it will not seat fully.

  5. The battery is the black rectangular piece in the bottom half of the device. Remove six 5mm screws holding down the battery using a Phillips PH0 screwdriver. Lift the battery and separate from its place holder.
    • The battery is the black rectangular piece in the bottom half of the device.

    • Remove six 5mm screws holding down the battery using a Phillips PH0 screwdriver.

    • Lift the battery and separate from its place holder.

    • Do not fully remove the battery as it is still connected by the connector in the top right corner.

  6. Using the nylon spudger, disconnect the white plugin. Once the wire has been disconnected you may remove the battery. Once the wire has been disconnected you may remove the battery.
    • Using the nylon spudger, disconnect the white plugin.

    • Once the wire has been disconnected you may remove the battery.

  7. Use a Phillips #0 screwdriver to remove the two 5 mm screws securing the fan. Use a Phillips #0 screwdriver to remove the two 5 mm screws securing the fan.
    • Use a Phillips #0 screwdriver to remove the two 5 mm screws securing the fan.

  8. Use a nylon spudger to push the wire (red/blue) plug out of its motherboard port. Be gentle and avoid applying extensive pressure when removing this plug, as the motherboard is fragile.
    • Use a nylon spudger to push the wire (red/blue) plug out of its motherboard port.

    • Be gentle and avoid applying extensive pressure when removing this plug, as the motherboard is fragile.

  9. Lift up the wire and peel back the clear protective tape. Split the black protective foam inside the tape in half to uncover the wires.
    • Lift up the wire and peel back the clear protective tape.

    • Split the black protective foam inside the tape in half to uncover the wires.

    • This step should free the wires free from their connections.

  10. Remove the fan from the motherboard. Remove the fan from the motherboard.
    • Remove the fan from the motherboard.

  11. Remove the two 4 mm screws from the heat sink with a Phillips #0 screwdriver. Lift and remove the heat sink from the CPU. Reapply thermal paste to the heat sink upon reassembly.
    • Remove the two 4 mm screws from the heat sink with a Phillips #0 screwdriver.

    • Lift and remove the heat sink from the CPU.

    • Reapply thermal paste to the heat sink upon reassembly.

  12. Use a plastic opening tool to flip up the black lock-bar on the ZIF connector, then disconnect the large orange ribbon cable. Use a plastic opening tool to flip up the black lock-bar on the ZIF connector, then disconnect the large orange ribbon cable. Use a plastic opening tool to flip up the black lock-bar on the ZIF connector, then disconnect the large orange ribbon cable.
    • Use a plastic opening tool to flip up the black lock-bar on the ZIF connector, then disconnect the large orange ribbon cable.

  13. Remove the clear tape covering the Wi-Fi card. Remove the clear tape covering the Wi-Fi card.
    • Remove the clear tape covering the Wi-Fi card.

  14. Remove the single 3 mm screw from the Wi-Fi card with a Phillips #0 screwdriver. Disconnect the Wi-Fi module from the motherboard by gently pulling the card out of its port. Disconnect the Wi-Fi module from the motherboard by gently pulling the card out of its port.
    • Remove the single 3 mm screw from the Wi-Fi card with a Phillips #0 screwdriver.

    • Disconnect the Wi-Fi module from the motherboard by gently pulling the card out of its port.

  15. Disconnect the plug from the motherboard using a Plastic Opening Tool. Disconnect the plug from the motherboard using a Plastic Opening Tool. Disconnect the plug from the motherboard using a Plastic Opening Tool.
    • Disconnect the plug from the motherboard using a Plastic Opening Tool.

  16. Remove the CMOS battery connector cable (red/black) from its port using a Nylon Spudger Tool. Remove the CMOS battery connector cable (red/black) from its port using a Nylon Spudger Tool. Remove the CMOS battery connector cable (red/black) from its port using a Nylon Spudger Tool.
    • Remove the CMOS battery connector cable (red/black) from its port using a Nylon Spudger Tool.

  17. Disconnect the cable from the motherboard using a Nylon Spudger. Disconnect the cable from the motherboard using a Nylon Spudger. Disconnect the cable from the motherboard using a Nylon Spudger.
    • Disconnect the cable from the motherboard using a Nylon Spudger.

  18. Use a Plastic Opening Tool to disconnect the black ribbon from the motherboard. Use a Plastic Opening Tool to disconnect the black ribbon from the motherboard. Use a Plastic Opening Tool to disconnect the black ribbon from the motherboard.
    • Use a Plastic Opening Tool to disconnect the black ribbon from the motherboard.

  19. Disconnect the white cable from the port by using a Plastic Opening Tool. Disconnect the white cable from the port by using a Plastic Opening Tool. Disconnect the white cable from the port by using a Plastic Opening Tool.
    • Disconnect the white cable from the port by using a Plastic Opening Tool.

  20. Remove the screen data cable from its connector. Remove the screen data cable from its connector. Remove the screen data cable from its connector.
    • Remove the screen data cable from its connector.

  21. Disconnect the DC power plug connector located at the top of the motherboard using a nylon spudger. Gently remove the whole piece from its  holder and place it aside. Gently remove the whole piece from its  holder and place it aside.
    • Disconnect the DC power plug connector located at the top of the motherboard using a nylon spudger.

    • Gently remove the whole piece from its holder and place it aside.

  22. Remove one Phillips #0 3 mm screw from the top of the motherboard. Gently lift the motherboard out of its casing to fully remove it from the device. Gently lift the motherboard out of its casing to fully remove it from the device.
    • Remove one Phillips #0 3 mm screw from the top of the motherboard.

    • Gently lift the motherboard out of its casing to fully remove it from the device.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Tanner Krygier

회원 가입일: 2018년 09월 17일

898 평판

안내서 5개 작성하였습니다

Washington State, Team S2-G7, Hope Fall 2018 Washington State, Team S2-G7, Hope Fall 2018 회원

WSU-HOPE-F18S2G7

3 회원들

안내서 5개 작성하였습니다

댓글 한 개

Seems to work with Z930 and Z935 as well. Nice guide!

RobloxRed - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 9

전체 시간: 760